remove-shower-drain Archives * flexco.com

5 Simple Steps on How to Take Out a Shower Drain

A clogged shower drain can be a nuisance, leading to slow drainage, unpleasant odors, and even water backups. If you encounter this issue, don’t panic! Taking out a shower drain is a relatively simple task that can be accomplished with basic tools and a little know-how. Whether you’re a seasoned DIYer or a complete novice, this guide will provide you with step-by-step instructions on how to unclog your shower drain effectively and efficiently.

Before delving into the process, it’s essential to gather the necessary tools. You’ll need a plunger, a pair of pliers, a drain snake, and a bucket or bowl. Additionally, protective gear such as gloves and safety glasses are recommended to prevent splashes and potential exposure to harmful chemicals. Once you have all the necessary equipment, you can proceed to the next step, which involves removing the drain cover.

Removing the drain cover is typically straightforward; most drain covers can be unscrewed or pried off using a screwdriver or a pair of pliers. Once the cover is removed, you’ll have direct access to the drain opening. Before inserting the drain snake, try using a plunger to dislodge the clog. If the plunger doesn’t do the trick, insert the drain snake into the drain opening and gently rotate it while pushing it down. The snake’s flexible design allows it to navigate bends and curves in the drain, helping to break up and remove the clog. Once the clog is removed, flush the drain with hot water to clear any remaining debris.

Identifying the Clog

Determining the location of the clog is crucial before attempting to remove it. Here are some common signs and tests to help you pinpoint the problem:

Slow Draining: Observe the flow rate of water in the shower. If it takes longer than usual to drain, there’s likely a partial clog.
Standing Water: If water accumulates around the drain after use, it indicates a more significant blockage.
Gurgling Noises: When water flows down a clogged drain, it can make a gurgling sound due to the air trapped in the blockage.
Test with Plunger: Place a plunger over the drain and pump vigorously. If the water level drops and then rises back up, the clog is likely located in the drain opening.
Hair or Debris: Inspect the drain opening for visible hair, soap scum, or other debris that may be causing the obstruction.
Chemical Drain Cleaners: Avoid using harsh chemical drain cleaners without first attempting mechanical removal methods. These cleaners can damage pipes and may not be effective for all types of clogs.

Here’s a table summarizing the potential location of clogs based on symptoms:

Symptom	Clog Location
Slow Draining	Partially clogged drain
Standing Water	Significant clog in drain or pipe
Gurgling Noises	Clog in drain, pipe, or vent
Plunger Only Partially Effective	Clog further down the pipe
Visible Hair or Debris	Clog in drain opening

Gathering Essential Tools

To effectively remove a shower drain, you will need a few essential tools. Gather the following items before you begin:

1. Plunger

A standard plunger can be used to dislodge clogs in shower drains. Choose a plunger with a suction cup that is large enough to cover the drain opening.

2. Drain Snake

A drain snake is a flexible tool used to reach clogs that are located further down the drainpipe. It consists of a long, thin cable with a hook or auger on the end. There are two main types of drain snakes: manual and powered.

Manual Drain Snake	Powered Drain Snake
Operated by hand	Powered by an electric motor
Less expensive	More expensive
Suitable for minor clogs	Suitable for stubborn clogs

3. Drain Cleaner

Commercial drain cleaners can be used to dissolve hair and other organic matter that may clog shower drains. Follow the manufacturer’s instructions carefully when using drain cleaners.

4. Bucket

A bucket is used to collect water and debris that will be removed from the drain.

5. Towels or rags

Towels or rags are used to wipe up any spills or water that may get on the floor.

Removing the Drain Cover

1. **Locate the Drain Cover:** The drain cover is typically a circular or square metal or plastic piece located in the center of the shower drain.

2. **Remove the Screws:** Using a screwdriver, carefully remove the screws that hold the drain cover in place. Some drain covers may not have screws and can be simply lifted out.

3. **Gently Lift the Drain Cover:** Once the screws are removed, gently lift the drain cover upward and away from the drain opening. Be careful not to drop the cover or apply excessive force, as it may damage the surrounding area.

Carefully inspect the drain cover to remove any visible debris or hair.

If the drain cover is heavily clogged or damaged, it may be necessary to replace it with a new one.

Tips for Removing a Clogged Drain Cover
Use a rubber glove to protect your hands from sharp edges or debris.
If the screws are rusted or difficult to remove, try using a penetrating lubricant to loosen them.
Once the drain cover is removed, you can use a flashlight to inspect the drain opening for any visible obstructions.

Using a Plunger

A plunger is a simple yet effective tool for unclogging shower drains. Follow these steps to use a plunger:

Fill the shower basin with a few inches of water to create a seal around the plunger.
Place the plunger over the drain and push down firmly, creating a vacuum.
Pull up sharply to create a suction force that dislodges the clog.
Repeat steps 2 and 3 several times, gradually increasing the force applied.

Tips for Using a Plunger

Use a plunger specifically designed for drains, as they have a wider base and a rubber cup that fits snugly over the drain.
Apply downward pressure steadily, not too quickly, as this can create excessive air pressure and burst the plunger.
If the clog is particularly stubborn, try using a smaller plunger and applying pressure directly to the center of the drain.
If the plunger doesn’t work, move on to other methods, such as using a drain snake or chemical cleaner.

Employing a Drain Snake

A drain snake, a flexible metal cable with a hook or auger tip, is a valuable tool for clearing shower drains. Here’s how to use it effectively:

1. Gather Your Materials

You’ll need a drain snake, a pair of gloves, a bucket, and a flashlight.

2. Remove the Drain Cover

Locate the drain cover in the center of the shower floor. Use a screwdriver or pliers to remove it carefully.

3. Insert the Drain Snake

With gloves on, insert the snake into the drain hole. If you encounter resistance, gently push and guide it down the drain.

4. Rotate and Push

Slowly rotate the snake while pushing it down. The hook or auger tip will catch and dislodge hair, soap scum, and other debris.

5. Work the Drain Snake Thoroughly

Insert and remove the snake several times, rotating it and pushing it deep into the drain. This ensures that all blockages are cleared.

Tips for Using a Drain Snake Effectively
– Use a flexible snake that can bend and navigate the curves of your drain.
– If the snake encounters resistance, don’t force it. Remove it and try again from a different angle.
– Use a flashlight to illuminate the drain and see where the blockage is located.
– Don’t be afraid to rotate and push the snake multiple times to ensure thorough cleaning.

Utilizing a Drain Cleaner

Drain cleaners, both commercial and homemade, can be effective in clearing minor clogs in shower drains. Here are the steps involved:

Commercial Drain Cleaners

Read and follow the product’s instructions carefully.
Pour the recommended amount of cleaner down the drain.
Let it sit for the specified time, usually 30-60 minutes.
Flush the drain with hot water to rinse out the cleaner.

Homemade Drain Cleaners

Baking Soda and Vinegar: Pour 1/2 cup of baking soda down the drain, followed by 1/2 cup of vinegar. Allow it to fizz for 10-15 minutes, then flush the drain with hot water.
Salt and Borax: Combine 1/2 cup of salt with 1/2 cup of borax. Pour the mixture down the drain and let it sit overnight. Flush the drain with hot water in the morning.
Enzymatic Drain Cleaners: Purchase an enzymatic drain cleaner that contains live bacteria that break down organic matter. Follow the product instructions for use, which typically involve pouring the cleaner down the drain and letting it sit for several hours or overnight.

Note: Avoid using both commercial and homemade drain cleaners together, as this can create toxic fumes. Also, never use drain cleaners on drains that are clogged with grease, as this can make the clog worse.

Clearing the P-Trap

The P-trap is a curved pipe located beneath the drain that holds water to create a seal and prevent sewer gases from escaping into the bathroom. Clogs often accumulate in this area, so it’s essential to check and clean the P-trap regularly to ensure proper drainage.

Materials Required:

– Adjustable wrench
– Bucket
– Towels or rags
– Screwdriver (optional)

Steps:

Place a bucket beneath the P-trap to catch any residual water.

Loosen the slip nuts at each end of the P-trap using an adjustable wrench. Rotate the nuts counterclockwise to unscrew them. Be cautious not to overtighten or damage the nuts.

Carefully remove the P-trap and inspect it for any clogs or debris. If there is standing water, tilt the P-trap to drain it into the bucket.

Clean the P-trap by removing any visible hair, soap scum, or other particles. Use a small brush or wire to dislodge any stubborn buildup. Rinse the P-trap thoroughly with hot water.

Inspect the rubber gasket inside the slip nuts for any wear or damage. Replace frayed or cracked gaskets to ensure a watertight seal.

Reinstall the P-trap by aligning the ends with the drain and slip nuts. Tighten the slip nuts clockwise using an adjustable wrench. Ensure the nuts are snug but not excessively tightened.

Check for leaks by running water down the drain. If any leaks occur, tighten the slip nuts further or inspect the P-trap for any cracks or damage. If necessary, use a screwdriver to tighten the screws that hold the P-trap in place.

Checking the Vent Stack

The vent stack is a crucial component of your plumbing system that allows air to flow freely through the drains. When the vent stack is blocked, it can cause slow drainage or even complete clogs.

To check the vent stack, locate the pipe that extends from your roof. This pipe will typically be larger in diameter than the other pipes on your roof. Pour a bucket of water down the main drain and observe the flow of water from the vent stack.

If the water flows freely, the vent stack is clear. If the water hesitates or backs up, the vent stack is likely clogged. You can try to clear the clog by pouring a mixture of baking soda and vinegar down the vent stack. If this doesn’t work, you may need to call a plumber to snake the vent stack.

Here are some additional tips for checking the vent stack:

Make sure that the vent stack is not blocked by any trees or bushes.
Check the roof to make sure that the vent stack is not damaged or corroded.
If you have a cap on your vent stack, make sure that it is not clogged or blocked.

By following these tips, you can easily check the vent stack on your home and ensure that it is functioning properly.

Symptom	Possible Cause
Slow drainage	Clogged vent stack
Complete clog	Blocked vent stack
Gurgling sounds from the drain	Clogged vent stack

Disassembling the Drain

To disassemble the drain, you will need the following tools:

Adjustable wrench
Pliers
Screwdriver
Bucket
Rags

Step 1: Remove the drain cover

Use a screwdriver to remove the screws that hold the drain cover in place. Once the screws are removed, lift the drain cover off.

Step 2: Remove the drain strainer

Once the drain cover is removed, you will see the drain strainer. Use a pair of pliers to remove the drain strainer.

Step 3: Remove the drain trap

The drain trap is the U-shaped pipe that is located under the drain strainer. Use an adjustable wrench to loosen the nuts that hold the drain trap in place. Once the nuts are loosened, remove the drain trap.

Step 4: Remove the drain pipe

The drain pipe is the pipe that connects the drain trap to the sewer line. Use an adjustable wrench to loosen the nuts that hold the drain pipe in place. Once the nuts are loosened, remove the drain pipe.

Step 5: Remove the drain flange

The drain flange is the metal plate that is located at the bottom of the drain pipe. Use an adjustable wrench to loosen the screws that hold the drain flange in place. Once the screws are loosened, remove the drain flange.

Step 6: Inspect the drain

Once the drain is disassembled, inspect the drain for any clogs or damage. If you find any clogs, use a drain snake to remove them. If you find any damage, you may need to replace the drain.

Step 7: Reassemble the drain

To reassemble the drain, reverse the steps that you took to disassemble it. Start by attaching the drain flange to the bottom of the drain pipe. Then, attach the drain pipe to the drain trap. Next, attach the drain strainer to the drain trap. Finally, replace the drain cover.

Seeking Professional Help

If the above methods prove ineffective, or if the clog is particularly severe, it may be necessary to seek professional help. A plumber can use specialized tools and techniques to clear the drain quickly and effectively.

Reasons to Call a Plumber:

Reason	Description
Frequent Clogs	Repeated drain clogs indicate an underlying issue that requires professional attention.
Persistent Bad Odors	Persistent bad odors emanating from the drain can indicate a buildup of bacteria or mold that requires professional cleaning.
Water Backing Up	If water starts backing up into the shower, it suggests a severe clog that requires immediate professional attention.
No DIY Success	If you have attempted multiple DIY methods without success, it’s best to seek professional help to avoid further damage.

How To Take Out A Shower Drain

A clogged shower drain is a common household problem that can be easily fixed with a few simple tools. Here are the steps on how to take out a shower drain:

Remove the drain cover. The drain cover is usually held in place by a few screws. Use a screwdriver to remove the screws and lift the drain cover off.
Locate the drain stopper. The drain stopper is a small, rubber or plastic plug that sits in the center of the drain. Use a pair of pliers to grip the drain stopper and pull it out.
Clean the drain stopper and drain. Use a toothbrush or a small brush to clean the drain stopper and the drain. Remove any hair, soap scum, or other debris that may be clogging the drain.
Reinsert the drain stopper. Push the drain stopper back into the drain. Make sure that it is seated properly so that it will create a watertight seal.
Replace the drain cover. Place the drain cover back over the drain and tighten the screws to secure it.

6 Clear-Cut Steps To Safely Remove A Shower Drain

If your shower drain is clogged, don’t despair. You can easily remove the drain cover and clean it out yourself. In this article, we’ll show you how to do it in just a few simple steps.

First, you need to gather your tools. You’ll need a pair of pliers, a screwdriver, and a bucket. If the drain cover is particularly stubborn, you may also need a hammer. Once you have your tools, you can begin the process of removing the drain cover.

To remove the drain cover, first use the pliers to loosen the screws that are holding it in place. Once the screws are loose, you can use the screwdriver to remove them completely. Once the screws are removed, you can lift the drain cover off of the drain. Be careful not to drop it, as it can be heavy. Once the drain cover is removed, you can clean it out. Use the bucket to catch any water or debris that comes out of the drain. Once the drain is clean, you can replace the drain cover. To do this, simply place the drain cover over the drain and tighten the screws. Make sure the drain cover is tight enough so that it won’t come loose again.

Determine the Type of Drain

Identifying Common Drain Types

Before attempting to remove a shower drain, it’s crucial to determine its type, as different drains have varying removal methods. Here are the most common types of shower drains:

Pop-up Drain

Characterized by a raised stopper that opens and closes the drain.

Usually secured by a screw or retainer ring at the base of the stopper.

Requires removal of the stopper before accessing the drain body.

Toe-Touch Drain

Activated by stepping on a lever or toe-touch mechanism on the drain cover.

Mechanism is connected to a plunger or other device that opens and closes the drain.

May require removal of the drain cover to access the mechanism.

Linear Drain

Long, narrow drain typically installed in the floor of the shower.

Covered by a grate or cover that can be removed for cleaning.

Drain body is usually secured by screws or bolts.

Gather Necessary Tools and Materials

Before tackling the task of removing a shower drain, you’ll need to gather the appropriate tools and materials. Here’s a comprehensive checklist to ensure you have everything you need:

Tools:

Plunger
Adjustable wrench or drain key
Screwdriver (Phillips or flathead, depending on screw type)
Needle-nose pliers
Wire hanger (optional)
Shop vacuum (optional)

Materials:

Drain cleaner (chemical or enzymatic)
Duct tape
Baking soda and vinegar (for DIY drain cleaning)
Replacement drain (if necessary)
Plumber’s putty or silicone sealant
Cloth or towel

Choosing the Right Drain Key:

Drain keys come in various sizes and shapes to fit different types of drains. To determine which key you need, measure the diameter of your drain opening and refer to the following table:

Drain Opening Diameter	Drain Key Size
1-1/2 inches	1/2-inch drain key
1-5/8 inches	3/4-inch drain key
2 inches	1-inch drain key

Unclog the Drain Using a Drain Snake

A drain snake is a flexible tool that can be used to remove clogs from drains. To use a drain snake, insert the end of the snake into the drain and slowly push it down. As you push the snake down, it will bend and follow the contours of the pipe. If the snake encounters a clog, it will push through it and break it up. Once the clog has been removed, pull the snake back out of the drain.

Here are some tips for using a drain snake:

Before using a drain snake, make sure that the water in the drain is turned off.
Use a flashlight to look down the drain and locate the clog.
Slowly insert the end of the snake into the drain and push it down.
If the snake encounters a clog, push harder to break it up.
Once the clog has been removed, pull the snake back out of the drain.
Run hot water through the drain to flush out any remaining debris.

Advantages of using a drain snake	Disadvantages of using a drain snake
Can be used to remove clogs from any type of drain	Can be difficult to use if the clog is located deep in the pipe
Relatively inexpensive	Can damage the drain if used improperly
Can be used to prevent clogs from forming	Requires some skill to use effectively

Use a Chemical Drain Cleaner

Chemical drain cleaners are a quick and easy way to unclog a shower drain. They are available at most hardware stores and home improvement centers. However, it is important to read the instructions carefully before using a chemical drain cleaner, as they can be harmful if not used properly.

Step 1: Prepare the area

Before using a chemical drain cleaner, make sure to remove any standing water from the shower. You can do this by using a wet/dry vacuum or a plunger. Once the water has been removed, place a towel around the drain to catch any spills.

Step 2: Read the instructions

Read the instructions on the drain cleaner carefully before using it. Follow the directions exactly as they are written.

Step 3: Pour the drain cleaner into the drain

Slowly pour the drain cleaner into the drain. Do not pour too much drain cleaner into the drain, as this can cause the drain to overflow.

Step 4: Let the drain cleaner work

Let the drain cleaner work for the amount of time specified on the instructions. Do not leave the drain cleaner in the drain for longer than the recommended time, as this can damage the pipes.

Step 5: Flush the drain with water

Once the drain cleaner has worked, flush the drain with plenty of water. This will help to remove any remaining drain cleaner and debris from the drain.

Chemical Drain Cleaner Safety Tips
– Never mix different types of chemical drain cleaners.
– Never use a chemical drain cleaner if the drain is already clogged with standing water.
– Always wear gloves and eye protection when using a chemical drain cleaner.
– Keep chemical drain cleaners out of reach of children.
– If you have any questions about using a chemical drain cleaner, consult a professional plumber.

Remove the Drain Trap

The drain trap is the curved section of pipe beneath the drain that collects hair and other debris to prevent it from entering the plumbing system. To remove the drain trap, follow these steps:

Place a bucket beneath the drain trap to catch any water that may spill out.
Using a pair of pliers or a wrench, loosen the nuts that hold the trap in place.
Carefully remove the trap from the drain.
Inspect the trap for any debris or clogs.
If there is any debris, clean it out with a wire brush or a pair of tweezers.
Reassemble the trap by screwing it back into place and tightening the nuts. Be sure not to overtighten the nuts, as this could damage the trap.

Tools Needed
Pliers or wrench
Bucket
Wire brush or tweezers

Once the drain trap is removed, you can access the clog and remove it. Be sure to wear gloves and eye protection when working on the drain, as there may be sharp edges or bacteria in the water.

Clean the Drain Trap

The drain trap is a U-shaped section of pipe located under the drain. Its purpose is to prevent sewer gases from entering the home. Over time, the trap can become clogged with hair and other debris, which can lead to slow drainage or even a complete blockage.

To clean the drain trap, you will need a bucket or shallow pan, a pair of pliers, and a small flashlight.

1. Place the bucket or pan under the drain trap to catch any water that may spill out.

2. Use the pliers to loosen the slip nuts that hold the trap in place.

3. Once the slip nuts are loose, you can remove the trap by pulling it down.

4. Inspect the trap for any clogs. If you see any hair or debris, remove it by hand.

5. Rinse the trap with clean water to remove any remaining debris.

6. Reinstall the trap by inserting it back into the drain pipe and tightening the slip nuts.

Reassemble the Drain

Now that you have cleaned all the parts of the drain, it’s time to reassemble it. Start by placing the rubber washer over the drain opening. Then, screw the drain flange into place. Make sure to tighten it securely, but not too tightly, or you could crack the flange. Next, place the strainer over the drain flange and secure it with the screws. Finally, replace the drain cover.

Tips for Reassembling the Drain

Use a little bit of plumber’s putty around the base of the drain flange to help seal it.
Don’t overtighten the screws. If you do, you could crack the flange or the strainer.
If you have a pop-up drain, make sure that the stopper is in the up position before you reassemble the drain.

Troubleshooting

If you have reassembled the drain and it’s still not working properly, there may be a problem with the drainpipe. To check the drainpipe, remove the drain flange and look inside the pipe. If there is any debris blocking the pipe, remove it and try reassembling the drain again.

Problem	Solution
Drain is leaking	Tighten the drain flange or replace the rubber washer.
Drain is clogged	Remove the strainer and clean out the debris.
Drain is not draining properly	Check the drainpipe for blockages.

Test the Drain

Before jumping into a deep cleaning, it’s essential to test the drain and determine the severity of the clog. Here are the steps involved in testing the drain:

Remove the Drain Cover: Use a screwdriver or pliers to remove the drain cover. This will provide access to the drain opening.
Fill the Drain with Water: Pour a cup or two of water into the drain. If the water drains quickly, the clog is likely minor. However, if the water remains stagnant or drains slowly, it indicates a more significant blockage.
Listen for Gurgling Sounds: While filling the drain with water, listen for any gurgling sounds coming from the pipes. Gurgling sounds indicate a partial blockage or possible issue in the plumbing system.
Check for Visible Blockages: Use a flashlight to inspect the drain opening for any visible blockages, such as hair, soap scum, or debris. Removing these blockages may solve the problem.
Test with a Plunger: If the water is not draining properly, try using a plunger to create a vacuum and dislodge the clog. Cover the drain opening completely with the plunger and vigorously plunge up and down to create suction.
Pour Baking Soda and Vinegar: Another home remedy to test the drain is to pour half a cup of baking soda down the drain, followed by half a cup of white vinegar. Let the mixture sit for 15 minutes, then flush with hot water.
Use a Drain Snake: If the plunger and baking soda method don’t work, you can try using a drain snake. Insert the snake into the drain opening and slowly feed it down the pipe while turning the handle to loosen the clog.
Consider Professional Help: If all the DIY methods fail to unclog the drain, it’s recommended to call a professional plumber to diagnose and clear the blockage effectively.

Clog Symptoms	Probable Causes
Slow drainage	Partial blockage, hair, soap scum, or debris
Stagnant water	Major blockage, mineral deposits, or foreign objects
Gurgling sounds	Partial blockage, air pockets, or plumbing issues
Unpleasant odors	Decaying organic matter, mold, or mildew

Prevent Future Clogs

Shower drains can get clogged for a variety of reasons, but there are a few things you can do to help prevent future clogs.

1. Remove hair regularly. Hair is one of the most common causes of shower clogs. To prevent hair from clogging your drain, remove it from the shower drain cover after each use. You can also use a drain strainer to catch hair before it gets into the drain.

2. Clean your drain regularly. Drains should be cleaned regularly to remove any buildup of soap, shampoo, and other products. You can clean your drain using a commercial drain cleaner or by pouring a cup of baking soda and a cup of vinegar down the drain.

3. Use a drain protector. Drain protectors are devices that fit over the drain and catch hair and other debris before it gets into the drain. Drain protectors are available in a variety of shapes and sizes, so you can find one that fits your drain and your needs.

4. Don’t pour grease or oil down the drain. Grease and oil can cause clogs in your drain. Instead of pouring grease or oil down the drain, dispose of it in a container or by putting it in the trash.

5. Avoid using harsh chemicals in your drain. Harsh chemicals can damage your drain and cause clogs. Instead of using harsh chemicals, use a gentle drain cleaner or a natural cleaning solution.

6. Regularly check the drain for buildup. Over time, soap scum, hair, and other debris can build up in your drain. To prevent clogs, regularly check the drain for buildup and remove any debris that you find.

7. Install a garbage disposal. A garbage disposal can help to grind up food waste and other debris before it gets into your drain. Garbage disposals can help to prevent clogs and keep your drain flowing smoothly.

8. Use a drain snake. A drain snake is a tool that can be used to remove clogs from your drain. Drain snakes are available in a variety of lengths and shapes, so you can find one that fits your drain and your needs.

9. Call a plumber. If you have a stubborn clog that you can’t remove on your own, you may need to call a plumber. Plumbers have the tools and experience to remove even the most stubborn clogs.

10. Shower drain maintenance schedule

Task	Frequency
Remove hair from drain cover	After each use
Clean drain	Monthly
Use drain protector	As needed
Don’t pour grease or oil down the drain	Always
Avoid using harsh chemicals in drain	Always
Regularly check drain for buildup	Monthly
Install a garbage disposal	As needed
Use a drain snake	As needed
Call a plumber	As needed

How to Get a Shower Drain Out

If your shower drain is clogged, you may be wondering how to get it out. There are a few different ways to do this, depending on the severity of the clog. For minor clogs, you can try using a drain cleaner. However, if the clog is more severe, you may need to remove the drain cover and snake the drain.

To remove the drain cover, you will need a screwdriver or a pair of pliers. Once the drain cover is removed, you can use a drain snake to clear the clog. A drain snake is a long, flexible wire with a hook on the end. You can insert the drain snake into the drain and use the hook to catch the clog. Once you have caught the clog, you can pull it out of the drain.

If you are unable to remove the clog using a drain cleaner or a drain snake, you may need to call a plumber. A plumber can use a hydro jet to clear the clog. A hydro jet is a high-pressure water jet that can break up even the most stubborn clogs.