remove-garbage-disposal Archives * flexco.com

10 Easy Steps: How To Remove A Garbage Disposal From Sink

Are you troubled by a garbage disposal that’s causing more trouble than it’s worth? Perhaps it’s jamming frequently, making strange noises, or simply not working as it should. Before you call a plumber, consider tackling the issue yourself. Removing a garbage disposal from your sink is a straightforward task that can be completed in a few simple steps. With the right tools and a bit of patience, you can save yourself the cost of a service call and the inconvenience of a non-functioning disposal.

Before you begin, ensure you have the necessary tools for the job. These include a bucket, a wrench, a screwdriver, and a pair of pliers. You’ll also need a flashlight to illuminate the work area and a pair of gloves to protect your hands. Once you have gathered your tools, clear the area around your sink and unplug the garbage disposal from the electrical outlet. Turn off the water supply to the sink and open the faucet to release any remaining water.

Now that you’re prepared, let’s begin the process of removing the garbage disposal. Locate the mounting nuts that connect the disposal to the sink flange. These nuts are typically located on the underside of the flange and can be loosened with a wrench. Once the nuts are loose, carefully separate the disposal from the flange. Be mindful of any wires or hoses that may be connected to the disposal and detach them accordingly. Finally, lift the garbage disposal out of the sink and place it in the bucket for disposal. Congratulations! You have successfully removed the garbage disposal from your sink.

Draining the Garbage Disposal

Before you begin working on the garbage disposal, it’s crucial to disconnect it from the power source. This can be done by flipping the circuit breaker or unplugging the appliance from the outlet. Once the power is disconnected, proceed with the following steps to drain the garbage disposal:

1. Locate the drain hose: Most garbage disposals have a drain hose connected to the bottom of the unit. This hose is typically made of plastic or rubber and runs to the underside of the sink.

2. Place a bucket or large container under the drain hose: The drain hose may contain water or debris, so it’s important to place a container underneath to catch any spills.

3. Open the drain valve: In most cases, the drain valve is a small knob or lever located on the body of the garbage disposal. Turn or lift the valve to open it and allow the water to drain into the container.

4. Wait for the water to drain completely: Once the drain valve is open, wait until all of the water has drained out of the garbage disposal. This may take a few minutes, depending on the amount of water present.

Once the garbage disposal is drained, you can proceed to the next steps of the removal process. Remember to exercise caution and follow safety guidelines when working with electrical or plumbing appliances.

Detaching the Drainpipe

The drainpipe expels water and waste from the garbage disposal. To detach it, follow these steps:

1. Access the Drainpipe

Locate the drainpipe connected to the bottom of the garbage disposal. It usually runs vertically down towards the floor.

2. Loosen the Connection

Using a basin wrench or pliers, loosen the slip nut or clamp that connects the drainpipe to the disposal. Turn it counterclockwise to loosen.

3. Disconnect the Pipe

Once the slip nut or clamp is loose, gently pull the drainpipe away from the disposal. If it’s difficult to remove, apply more force with the wrench or pliers.

4. Drain the Water (Optional)

If water is still present in the drainpipe, position a bucket or basin underneath the disconnected end to catch it. Wait for the water to drain out completely before proceeding.

Pro Tip: Use a flashlight or phone light to illuminate the area under the sink for better visibility.

Disconnecting the Dishwasher Line

1. Turn off the water supply to the dishwasher. Locate the shut-off valve under the sink and turn it clockwise to close it.

2. Disconnect the hot and cold water lines from the dishwasher. Use a wrench or pliers to loosen the nuts connecting the lines to the dishwasher and pull them off.

3. Cap the water lines. Use a pair of pliers to attach a cap to each of the water lines to prevent water from leaking out.

4. Remove the drain hose from the garbage disposal. Use a pair of pliers to loosen the clamp connecting the hose to the disposal and pull the hose off.

5. **Disconnect the electrical wires from the dishwasher.**

Locate the electrical junction box under the sink.
Turn off the circuit breaker or remove the fuse that supplies power to the dishwasher.
Unscrew the screws holding the junction box cover in place and remove the cover.
Locate the wires connected to the dishwasher and disconnect them using a screwdriver or wire cutter.
Cap the wires using electrical tape or wire nuts.

6. Remove the dishwasher from the sink base. Use a screwdriver or drill to remove the screws securing the dishwasher to the sink base.

7. Lift the dishwasher out of the sink base and set it aside.

Lowering the Garbage Disposal

Safety Precautions

Before proceeding, ensure the garbage disposal is unplugged from the power source and the water supply is turned off at the stop valves under the sink. Wear safety gloves and glasses to protect yourself from potential contact with sharp edges or electrical components.

Disconnect the Plumbing

Inspect the garbage disposal’s plumbing connections. Typically, there will be two pipes connected: the drain pipe leading to the sink and the dishwasher drain hose. Disconnect these connections by carefully loosening the clamps or couplings using a wrench or pliers.

Support the Disposal

Once the plumbing is disconnected, support the garbage disposal’s weight with one hand while working on the other side. It’s advisable to use a towel or cloth to avoid scratching the sink or countertop.

Remove the Mount

Locate the mounting bracket or flange that secures the garbage disposal to the sink. It may be held in place by screws or bolts. Use a screwdriver or wrench to remove the fasteners, taking care not to drop any components into the garbage disposal.

Carefully Lower the Disposal

With the mount removed, gently lower the garbage disposal unit towards the bottom of the sink. Guide it carefully, avoiding contact with any electrical wires or other sink fixtures. Once the disposal is fully lowered, remove your hand from supporting it.

Check for Obstructions

Inspect the area around the garbage disposal for any blockages or obstacles that may prevent it from being removed. If any obstructions are found, carefully clear them out before continuing.

Removing the Electrical Wires

Before you attempt to remove the electrical wires from your garbage disposal, be sure to turn off the power at the circuit breaker. Once the power is off, you can follow these steps:

1. Locate the junction box that houses the electrical wires for the garbage disposal. The junction box is usually located under the sink.

2. Open the junction box by removing the screws that hold the cover in place.

3. Inside the junction box, you will see the electrical wires for the garbage disposal. The wires will be connected to the garbage disposal and to the power supply.

4. To disconnect the electrical wires from the garbage disposal, use a screwdriver to loosen the screws that hold the wires in place.

5. Once the screws are loose, carefully pull the wires away from the garbage disposal.

6. Once the wires are disconnected from the garbage disposal, you can remove the junction box from the wall.

7. To remove the electrical wires from the power supply, follow these steps:

a. Turn off the power to the circuit breaker that supplies power to the garbage disposal.

b. Remove the cover plate from the electrical outlet.

c. Inside the electrical outlet, you will see the electrical wires for the garbage disposal. The wires will be connected to the power supply.

d. To disconnect the electrical wires from the power supply, use a screwdriver to loosen the screws that hold the wires in place.

e. Once the screws are loose, carefully pull the wires away from the power supply.

f. Once the wires are disconnected from the power supply, you can remove the electrical wires from the wall.

Unmounting the Disposal Unit

1. Turn off the water supply to the sink before starting any work.

2. Disconnect the power supply to the disposal unit by unplugging it from the electrical outlet.

3. Place a bucket or towel under the disposal unit to catch any water or debris.

4. Use a wrench to loosen the mounting bolts that secure the disposal unit to the sink flange.

5. Once the mounting bolts are loose, carefully lift the disposal unit up and off the sink flange.

6. Disconnect the discharge hose from the disposal unit.

7. Disconnect the electrical cord from the disposal unit.

Removing the Sink Flange

8. If you need to remove the sink flange, use a utility knife to cut the sealant around the flange. Then, use a screwdriver to remove the screws that secure the flange to the sink. Once the screws are removed, you should be able to lift the flange off the sink.

9. Once the disposal unit is disconnected, you can remove it from the sink.

10. Clean the sink flange and the area around the disposal unit with a mild detergent and water.

Cleaning the Sink Area

Cleaning the sink area before removing the garbage disposal is crucial to ensure a safe and hygienic work environment. Here’s a step-by-step guide to cleaning the area thoroughly:

Remove any Obstacles

Clear the sink and surrounding area of any dishes, utensils, or sponges to create a spacious work area.

Turn Off Water Supply

Locate the shut-off valves under the sink and turn them off to prevent water from flowing while working.

Wear Protective Gear

Put on gloves and safety glasses to protect your hands and eyes from potential splashes or debris.

Cover Drain Opening

Use a drain plug or a damp cloth to cover the drain opening and prevent small parts from accidentally falling down the drain.

Clean the Sink Surface

Use a non-abrasive cleanser and a sponge to clean the sink surface, paying attention to any food residue or grease buildup.

Disinfect the Sink

Apply a disinfectant solution to the sink surface and let it sit for the recommended time to kill bacteria and germs.

Rinse the Sink

Thoroughly rinse the sink with clean water to remove any remaining cleanser or disinfectant.

Wipe Dry

Use a clean towel or paper towels to wipe the sink dry and remove any excess moisture.

Set Up a Bucket

Place a bucket or large bowl under the sink to catch any water or debris that may fall while removing the garbage disposal.

Tools and Materials:
Gloves
Safety glasses
Drain plug or damp cloth
Non-abrasive cleanser
Sponge
Disinfectant solution
Clean towel or paper towels
Bucket or large bowl

Preparing for Installation

Before you start the removal process, ensure you’re well-prepared with the necessary tools and knowledge.

Safety Measures

1. Disconnect the garbage disposal from the power source.
2. Turn off the water supply to the kitchen sink.
3. Put on safety gloves to protect your hands from sharp edges.

Tools Required

4. Adjustable wrench
5. Plumber’s putty
6. Bucket or bowl
7. Flashlight or work light

Additional Tips

8. Take pictures of the current setup for reference during reinstallation.
9. Keep a flashlight or work light nearby for illumination in cramped spaces.
10. If you encounter any stubborn connections or bolts, apply penetrating oil to loosen them up. Allow the oil to soak in for a few minutes before attempting to remove them. However, avoid using excessive force, as this could damage the components.

Gather Additional Help

If you’re unsure or uncomfortable working on plumbing, don’t hesitate to call a qualified plumber for assistance. Their experience and expertise will ensure the safe and efficient removal of your garbage disposal.

How To Remove A Garbage Disposal From Sink

A garbage disposal is a convenient appliance that can help to keep your kitchen clean and free of food waste. However, if your garbage disposal is not working properly, it may need to be removed and replaced. Removing a garbage disposal can be a challenging task, but it is possible to do it yourself with the right tools and instructions.

Before you begin, you will need to gather the following tools:

A Phillips head screwdriver
A flat head screwdriver
A pair of pliers
A bucket
A flashlight

Once you have gathered your tools, you can begin the process of removing your garbage disposal.

1. Turn off the power to your garbage disposal at the circuit breaker. This will prevent you from getting shocked while you are working.

2. Disconnect the water supply to your garbage disposal. There will be a shut-off valve located under the sink. Turn the valve clockwise to turn off the water.

3. Place a bucket under the garbage disposal to catch any water that may leak out.

4. Use the pliers to disconnect the drain hose from the garbage disposal. The drain hose is the black hose that connects the garbage disposal to the sink drain.

5. Use the Phillips head screwdriver to remove the mounting bolts that hold the garbage disposal in place. There will typically be three or four mounting bolts.

6. Once the mounting bolts have been removed, you can carefully lift the garbage disposal out of the sink.

7. Inspect the old garbage disposal for any damage. If the garbage disposal is damaged, you will need to replace it.

8. If the garbage disposal is not damaged, you can reinstall it by following the steps in reverse order.

7 Simple Steps to Remove a Badger Garbage Disposal

Are you tired of your kitchen sink being clogged by FOG (fats, oils, and grease)? Do you dread the thought of having to call a plumber to fix your garbage disposal? If so, then you need to learn how to remove a badger garbage disposal. Removing a badger garbage disposal is not as difficult as you may think, and it is a task that can be completed in just a few minutes. In this article, we will provide you with step-by-step instructions on how to remove a badger garbage disposal.

Before you begin, you will need to gather a few tools. These tools include a flashlight, a pair of pliers, a screwdriver, and a bucket. Once you have gathered your tools, you can begin the process of removing your badger garbage disposal. The first step is to turn off the power to your garbage disposal. You can do this by flipping the circuit breaker or by unplugging the garbage disposal from the outlet. Once the power is turned off, you can begin to remove the badger garbage disposal. To remove the badger garbage disposal, you will need to locate the two mounting screws that are located on the bottom of the disposal. Once you have located the mounting screws, you can use the screwdriver to remove them. Once the mounting screws are removed, you can pull the badger garbage disposal away from the sink.

Once you have removed the badger garbage disposal, you can clean it. To clean the badger garbage disposal, you can use a mild detergent and a soft cloth. Once the badger garbage disposal is clean, you can reinstall it. To reinstall the badger garbage disposal, you will need to reverse the steps that you took to remove it. Once the badger garbage disposal is reinstalled, you can turn on the power and test it to make sure that it is working properly.

Identifying the Circuit Breaker or Fuse

Before you begin any work on the garbage disposal, it is crucial to ensure the power to the unit is turned off. This safety precaution prevents electrical shock and ensures you can work safely. Identifying the correct circuit breaker or fuse that controls the disposal is the first step in isolating the power.

Start by locating the electrical panel, which typically resides in a basement, garage, or utility closet. Once you have identified the electrical panel, carefully inspect the circuit breakers or fuses inside. Each breaker or fuse will have a label or identification indicating the circuit it controls. Look for a breaker or fuse labeled “garbage disposal,” “kitchen,” or “appliances.” If you cannot find a specific label for the disposal, you may need to test each circuit breaker or fuse to determine which one controls the unit.

To test the circuit breakers, flip each one to the “OFF” position. Then, try to operate the garbage disposal. If the disposal does not operate, you have identified the correct circuit breaker. Alternatively, you can use a non-contact voltage tester to identify the live circuit. However, always remember to exercise caution when working with electricity and consult a qualified electrician if you are unsure.

Circuit Breaker	Description
Single-pole breaker	Controls a single circuit, typically used for lighting or outlets
Double-pole breaker	Controls two circuits, typically used for major appliances like ovens or dryers
Fuse	A thin wire that melts when too much current flows through it, protecting the circuit

Shutting Off the Water Supply

Before attempting to remove your Badger garbage disposal, it is crucial to shut off the water supply. This will prevent any water from spraying out when you disconnect the disposal.

1. Locate the water supply valves:

The water supply valves are typically located under the sink. They are usually two valves, one for hot water and one for cold water.

2. Turn off the water supply valves:

To turn off the water supply valves, simply turn them clockwise until they are completely closed. You may need to use a wrench or pliers to tighten them securely.

3. Here is a step-by-step guide on how to turn off the water supply to your Badger garbage disposal using the two types of water supply valves:

Type of Valve	Instructions
Compression Valve:	Turn the handle clockwise until it is hand-tight. Do not overtighten.
Gate Valve:	Turn the handle clockwise until it stops. Do not overtighten.

Accessing the Disposal

Locate the disposal under the sink. It is typically a cylindrical unit with a metal flange and a rubber gasket. The flange is usually attached to the sink drain with screws or bolts.

Disconnecting the Power

Turn off the power to the disposal at the circuit breaker or fuse box. This is a critical safety step to prevent electric shock.

Accessing the Mounting Bolts

Reach under the sink and locate the mounting bolts that hold the disposal in place. There are typically four bolts, two on each side of the flange. These bolts may be difficult to reach, so you may need to use a flashlight or a mirror to see them.

Once you have located the mounting bolts, use a wrench to loosen them. Do not remove the bolts completely; just loosen them enough so that you can remove the disposal.

Grip the disposal firmly and pull it straight down to detach it from the sink drain. Be careful not to drop the disposal, as it is heavy.

If the Mounting Bolts are Rusted or Corroded

If the mounting bolts are rusted or corroded, you may need to use penetrating oil to loosen them. Apply the penetrating oil to the bolts and let it sit for several minutes before trying to loosen them.

Tool	Description
Wrench	Used to loosen the mounting bolts.
Flashlight or mirror	Used to locate the mounting bolts if they are difficult to see.
Penetrating oil	Used to loosen rusted or corroded mounting bolts.

Disconnecting the Wires

Before you can remove a Badger garbage disposal, you need to disconnect the wires. This can be a bit tricky, but it’s important to do it safely. Here are the steps to follow:

1. Disconnect the Power

Turn off the power to the garbage disposal at the circuit breaker. This will prevent you from getting shocked while you’re working.

2. Remove the Faceplate

Use a screwdriver to remove the screws that hold the faceplate in place. Once the faceplate is removed, you’ll see the wires that are connected to the garbage disposal.

3. Identify the Wires

There are three wires that are connected to the garbage disposal: black, white, and green. The black wire is the hot wire, the white wire is the neutral wire, and the green wire is the ground wire. It’s important to identify these wires before you disconnect them.

4. Disconnect the Wires

Use a pair of needle-nose pliers to disconnect the wires. Be careful not to touch the bare ends of the wires, as this could give you a shock. Once the wires are disconnected, you can remove the garbage disposal from the sink.

Wire Color	Function
Black	Hot wire
White	Neutral wire
Green	Ground wire

Removing the Drain Line

Removing the drain line is a critical step in removing a Badger garbage disposal. Here’s a detailed guide on how to do it:

Prepare your tools: You’ll need a bucket, wrench, pliers, and a flashlight.
Clear the sink: Place a bucket beneath the drain to catch water and debris.
Locate the drain line: It’s usually a corrugated pipe connected to the garbage disposal’s outlet.
Disconnect the drain line: Use a wrench to loosen the nuts or clamps securing the drain line to the disposal. Be careful not to damage the pipes.
Inspect and clean the line: Remove any clogs or debris from the drain line using a plumber’s snake or drain cleaner. If it’s heavily clogged, you may need to replace it.

Cleaning the drain line is crucial for optimal performance of your new garbage disposal. Here’s a table summarizing the possible cleaning methods:

Method	Description
Plumber’s snake	Inserts a flexible coil into the line to break up clogs.
Drain cleaner	Chemical solution that dissolves organic clogs.
Hydro-jetting	High-pressure water stream that clears stubborn clogs.

Reconnect the drain line: Once cleaned, reconnect the drain line to the garbage disposal and tighten the nuts or clamps securely.

Unmounting the Disposal

1. **Disconnect the power supply.** Turn off the circuit breaker or remove the fuse to the disposal unit.
2. **Disconnect the water supply.** Locate the water supply lines under the sink and shut off the valves.
3. **Remove the drain hose.** Pull the hose clamp back and detach the hose from the disposal outlet.
4. **Remove the mounting bolts.** There are typically four bolts that secure the disposal to the countertop and sink. Use a socket wrench or adjustable wrench to remove the bolts.
5. **Lower the disposal.** Once the bolts are removed, carefully lower the disposal by hand. Be aware that the disposal may be heavy.
6. **Unwire the disposal.** Locate the electrical wires connected to the disposal. Use a pair of wire cutters to cut the wires, leaving a few inches of exposed wire. Cap the exposed wires with electrical tape for safety.

Disconnecting the Dishwasher Drain Hose

If your dishwasher is connected to the disposal, you will need to disconnect its drain hose as well.

Step	Action
1	Locate the dishwasher drain hose under the sink.
2	Pull the hose clamp back and detach the hose from the disposal outlet.
3	Plug the end of the drain hose with a rubber stopper or cap.

Disassembling the Disposal

Step 1: Safety First

Before handling the disposal, unplug it from the power outlet. Ensure the base is empty and the power supply is cut off to prevent any electrical hazards.

Step 2: Locate the Mounting Ring

Find the mounting ring that connects the disposal to the sink flange. It’s usually a metal ring with screws or bolts.

Step 3: Disconnect the Plumbing

Loosen the connections where the drain and water supply lines attach to the disposal. Use a wrench or pliers, and be careful not to damage the lines.

Step 4: Detach the Disposal from the Sink

Using a screwdriver, remove the screws or bolts that attach the mounting ring to the sink flange. Gently lift the disposal off the flange and set it aside.

Step 5: Remove the Power Cord

Locate the junction box where the power cord connects to the disposal. Open the box and disconnect the cord.

Step 6: Separate the Motor and Grind Chamber

Unbolt the small motor housing from the larger grind chamber. The motor housing contains the electric motor that drives the blades.

Step 7: Disassemble the Grind Chamber

Inspect the grind chamber for any wear or damage. If necessary, loosen the bolts that hold the grinding ring in place and remove it. The impellers and splash guard can also be removed for further inspection and cleaning.

Cleaning the Disposal

Cleaning your Badger garbage disposal regularly is essential to keep it running smoothly and free of unpleasant odors. Here’s a detailed guide on how to clean your disposal effectively:

1. Turn Off the Power

Before cleaning the disposal, ensure that it is turned off at the circuit breaker or under-sink switch to prevent any accidental activation.

2. Remove the Splash Guard

Most Badger garbage disposals have a removable splash guard. Lift it off by grasping the tab and pulling it straight up.

3. Use Ice and Salt

Fill the disposal chamber with a cup of ice and half a cup of salt. Run the disposal for a few seconds to grind the ice and salt. This combination helps to eliminate odors and remove debris.

4. Use a Dish Soap and Water Solution

Mix a few tablespoons of dish soap with warm water in a small bowl. Pour the solution into the disposal and run it for 30 seconds to remove any remaining food particles and grease.

5. Use Citrus Peels

Citrus peels, such as lemon or orange peels, contain d-limonene, a natural solvent that can help break down grease and debris. Place several peels into the disposal and run it for 15 seconds.

6. Run Hot Water

After cleaning, pour a cup of hot water down the disposal to flush out any loosened debris and rinse the chamber.

7. Disinfect with Bleach

To disinfect the disposal, mix 1/4 cup of bleach with four cups of cold water in a bowl. Pour the solution into the disposal and let it sit for 30 minutes before running it for 15 seconds.

8. Detailed Cleaning

For a more thorough cleaning, use a flashlight to inspect the disposal chamber for any visible debris or clogs. Use a pair of tongs or tweezers to remove any large objects. You can also use a brush or sponge to scrub the disposal rim and blades to remove any stuck-on particles.

Following these steps regularly will help maintain your Badger garbage disposal and prevent any potential problems.

Reassembling the Disposal

Once the disposal has been cleaned, it’s time to reassemble it. This is a relatively simple process, but it’s important to follow the steps carefully to ensure that the disposal is working properly.

Step 1: Align the mounting bracket with the holes in the sink flange. Secure the bracket with the screws provided.

Step 2: Insert the disposal into the mounting bracket. Turn the disposal clockwise until it is fully seated.

Step 3: Connect the electrical wires. Wrap the black wire around the black terminal and tighten the screw. Wrap the white wire around the white terminal and tighten the screw.

Step 4: Connect the drain line. Insert the rubber gasket into the drain hole in the sink. Slide the drain line onto the gasket and tighten the clamp.

Step 5: Test the disposal. Run water into the sink and turn on the disposal. The disposal should run smoothly and quietly.

Step 6: If the disposal is leaking, check the following:

Possible Leak	Cause	Solution
Leak from the mounting bracket	Loose screws	Tighten the screws
Leak from the electrical connections	Loose wires	Tighten the screws
Leak from the drain line	Loose clamp or damaged gasket	Tighten the clamp or replace the gasket

Reconnecting the Disposal

Once the disposal is removed, it’s time to reconnect the new one. To do this, follow these steps:

Clean the mounting surface. Remove any old sealant or debris from the mounting surface of the sink.
Apply a bead of sealant. Apply a thin bead of plumber’s putty or silicone sealant around the mounting surface.
Position the disposal. Carefully position the disposal over the mounting surface, making sure that the flange is flush with the sink.
Tighten the mounting bolts. Using a screwdriver, tighten the mounting bolts that hold the disposal in place.
Connect the plumbing. Connect the drain line and dishwasher hose to the disposal.
Test the disposal. Turn on the faucet and run water through the disposal. Check for any leaks or unusual noises.
Reset the disposal. Press the reset button on the bottom of the disposal if it is not running properly.
Install the drain stopper. Install the drain stopper in the sink.
Caulk around the disposal. Apply a bead of caulk around the edge of the disposal where it meets the sink.
Allow the caulk to dry. Allow the caulk to dry completely before using the disposal. This will help to prevent leaks and ensure a secure connection. Here is a table summarizing the steps for reconnecting the disposal:

Step	Action
1	Clean the mounting surface.
2	Apply a bead of sealant.
3	Position the disposal.
4	Tighten the mounting bolts.
5	Connect the plumbing.
6	Test the disposal.
7	Reset the disposal.
8	Install the drain stopper.
9	Caulk around the disposal.
10	Allow the caulk to dry.

How to Remove a Badger Garbage Disposal

Removing a Badger garbage disposal is a relatively straightforward process, but it does require some basic plumbing knowledge and tools. Here are the steps on how to remove a Badger garbage disposal:

Turn off the power to the garbage disposal. This can be done by flipping the breaker that powers the disposal or by unplugging the disposal from the outlet.
Turn off the water supply to the garbage disposal. This is typically done by closing the shut-off valve located under the sink.
Disconnect the drain line from the garbage disposal. The drain line is the large hose that connects the disposal to the sink drain. To disconnect the drain line, loosen the clamp that holds the hose in place and then pull the hose off of the disposal.
Disconnect the electrical wiring from the garbage disposal. The electrical wiring is typically held in place by a plastic cover. To disconnect the electrical wiring, remove the cover and then disconnect the wires from the disposal.
Unscrew the mounting bolts that hold the garbage disposal in place. There are typically four mounting bolts that hold the disposal in place. To unscrew the mounting bolts, use a socket wrench or a screwdriver.
Remove the garbage disposal from the sink. Once the mounting bolts have been removed, you should be able to lift the garbage disposal out of the sink.