quarter-round Archives * flexco.com

10 Simple Steps to Seamlessly Cut Quarter Round Inside Corners

Quarter-round molding adds a decorative and finished look to the corners of your walls and baseboards. While cutting inside corners can be a bit tricky, it’s definitely doable with the right tools and techniques. In this article, we’ll walk you through the steps on how to cut quarter-round inside corner like a pro.

To begin, you’ll need a few essential tools: a miter saw, a measuring tape, a pencil, and a sander. Once you have your tools gathered, you can start by measuring and marking the length of the quarter-round molding that you need. Be sure to add a little extra length to each piece to account for the miter cuts. Next, set up your miter saw at a 45-degree angle. This will allow you to cut the miters that will form the inside corner.

When you’re cutting the miters, it’s important to make sure that the molding is positioned correctly on the saw. The top of the molding should be facing the fence, and the miter cut should be made on the inside edge of the molding. Once you’ve cut both miters, dry-fit the pieces together to make sure that they fit properly. If the fit is too tight, you can sand down the edges of the miters slightly. If the fit is too loose, you can add a thin strip of wood or cardboard to the inside of the corner.

Measuring and Marking the Cut

To cut a quarter round inside corner, you’ll need to measure and mark the cut accurately. Here’s a step-by-step guide:

Measuring and Marking the Miter Cut

1. Measure and mark the length of the quarter round: Measure the length of the inside corner where you want to install the quarter round. Mark this length on the quarter round using a measuring tape and a pencil.

2. Find the center point of the quarter round: Measure the width of the quarter round and divide it in half. Mark the center point on the length you marked earlier.

3. Draw a 45-degree angle line from the center point: Use a protractor or a miter saw to draw a 45-degree angle line from the center point to the edge of the quarter round. This line will mark the angle for the miter cut.

4. Mark the miter cut: Draw a line perpendicular to the 45-degree angle line, starting from the edge of the quarter round and extending beyond the length you marked earlier. This line will mark the miter cut.

5. Repeat for the other inside corner: Repeat steps 1-4 for the other inside corner. Make sure that the miter cuts are facing each other.

Setting Up the Miter Saw

Getting your miter saw ready is crucial for precise quarter-round inside corner cuts. Here’s a detailed guide to help you set it up correctly:

1. Make Sure the Saw Is Square

Use a carpenter’s square to check if the saw blade is perpendicular to the saw table. If not, adjust the saw’s fence or miter gauge until the blade is perfectly square. This ensures that your cuts will be straight and accurate.

2. Set the Miter Gauge to 45 Degrees

Unlock the miter gauge and set it to 45 degrees. Measure the angle with a protractor or use the pre-calibrated miter gauge scale. Ensure that the gauge is firmly locked in place, and the saw blade is parallel to the miter slot.

**Note:** Quarter-round moldings have a convex and concave side. Make sure the molding is facing the right way so that it fits snugly into the corner once cut.

3. Support the Trim

Place a piece of scrap lumber or a support stand on both sides of the saw blade to support the molding while cutting. This prevents the molding from sagging or moving during the cut, resulting in clean and precise angles.

Making the Initial Cut

The initial cut is crucial for ensuring a precise and clean inside corner joint. Here’s how to perform this step accurately:
1. Measure and mark the length of the quarter round.
2. Place the quarter round on the miter saw at a 45-degree angle.
3. Secure the quarter round firmly in place using the saw’s clamps.
4. Position the saw blade carefully so that it aligns with the mark on the quarter round.
5. Slowly lower the saw blade and make the initial 45-degree cut. Ensure that the blade cuts through the entire thickness of the quarter round.

Tip:
For more precise cuts, use a sharp saw blade specifically designed for cutting wood moldings.
Wear safety glasses to protect your eyes from sawdust and flying debris during cutting.
Test the fit of the initial cut by temporarily assembling the two pieces of quarter round together. If the fit is not tight, adjust the cut angle slightly and repeat the process until the joint fits snugly.

Trimming the Trim

Before you begin cutting the quarter-round inside corner, you’ll need to trim the trim. This will help to ensure that the pieces fit together snugly and create a clean, professional-looking finish.

To trim the trim, follow these steps:

1. Measure the length of the inside corner.
2. Cut two pieces of quarter-round trim to the measured length.
3. Place one piece of trim against the inside corner, flush with the edge of the wall.
4. Mitering the Trim:
– Mark the trim at the point where it intersects the inside corner.
– Use a miter saw or a miter box to cut a 45-degree angle on the end of the trim, starting at the marked point and cutting towards the inside corner.
– Repeat this process for the other piece of trim.
– Test-fit the mitered pieces together to ensure a snug fit. If necessary, adjust the angles on the miter cuts until the pieces fit perfectly.

Fitting and Adjusting the Cut

Once you have a rough cut, you can start to fine-tune it for a perfect fit. Here are some tips:

Hold the pieces together: Place the two pieces of quarter round together at the corner. Make sure the edges are flush and the ends are aligned.
Test the fit: Hold the pieces up to the corner where they will be installed. If there are any gaps or overlaps, you will need to adjust the cut.
Adjust the cut: Use a sharp knife or miter saw to shave off small amounts of material from the ends of the pieces. Be careful not to cut too much, as this can weaken the joint.
Re-test the fit: Repeat steps 2 and 3 until the pieces fit together snugly without any gaps or overlaps.
Finish the cut: Once you are satisfied with the fit, use a fine-grit sandpaper to smooth the edges of the cut. This will help to create a clean and professional-looking finish.

Here is a table summarizing the steps involved in fitting and adjusting the cut:

Step	Description
1	Hold the pieces together and align the edges and ends.
2	Test the fit at the corner.
3	Adjust the cut by shaving off small amounts of material from the ends of the pieces.
4	Re-test the fit until the pieces fit snugly without any gaps or overlaps.
5	Finish the cut by smoothing the edges with fine-grit sandpaper.

Cutting Multiple Corners

When cutting multiple inside corners for quarter round, it’s crucial to ensure a precise and consistent fit throughout the project. Here’s a detailed guide to achieve seamless corners with multiple cuts:

1. Mark the Corner Points

Use a pencil to mark the exact point where the two pieces of quarter round will meet at the inside corner.

2. Position the Miter Box

Place the miter box on a flat and stable surface, ensuring that the 45-degree angled slots face outwards. Align the marked corner point with the “zero” mark on the miter box.

3. Insert the Quarter Round

Insert one piece of quarter round into the miter box, aligning the bottom edge with the base of the box and the marked corner point with the “zero” mark. Secure the quarter round firmly.

4. Cut the First Angle

Using a fine-toothed saw, carefully cut along the 45-degree angled slot of the miter box. Repeat this process for the second piece of quarter round.

5. Dry Fit the Pieces

Dry fit the two cut pieces together at the corner to ensure a snug fit. If there are any gaps or overlaps, adjust the miter box angles slightly and recut the quarter round until a perfect fit is achieved.

6. Apply Adhesive and Secure

Once the miter cuts are precise, apply a layer of wood glue or construction adhesive to the inside edges of both pieces of quarter round. Carefully insert the pieces into the corner and hold them firmly in place for several minutes to allow the adhesive to dry.

Corner Type	Miter Box Angle(s)	Cut Direction
Inside 90°	45°, 45°	Inward, Inward
Inside 45°	22.5°, 22.5°	Inward, Inward
Inside 30°	15°, 15°	Inward, Inward

Using a Miter Box

Using a miter box is the simplest but also one of the most precise ways to cut quarter round inside corners. A miter box is a wooden or plastic tool that contains a series of angled slots. This allows you to safely and easily cut angles in a variety of materials.

1. Measure and mark the length of quarter round you need for each side of the inside corner.

2. Cut the quarter round using a miter saw.

3. Place the quarter round in the miter box with the back side facing up.

4. Align the mark on the quarter round with the desired angle on the miter box.

5. Hold the saw firmly in your hand and make a smooth, even cut.

6. Repeat steps 3-5 to cut the other side of the inside corner.

7. Test fit the quarter round in the inside corner. You can use a coping saw, block plane, or sandpaper to make any necessary adjustments for a perfect fit.

Tool	Description	Use
Coping Saw	A small, handheld saw with a narrow, flexible blade	For cutting intricate or curved shapes in quarter round
Block Plane	A small, handheld plane with a flat bottom and an adjustable blade depth	For smoothing and flattening the surface of quarter round
Sandpaper	A flexible abrasive paper used for smoothing and shaping wood surfaces	For making minor adjustments to the fit of quarter round

Scribing the Cut

Scribing the cut ensures a precise and seamless fit. To scribe the cut:

1. Position the two quarter round pieces together at a 90-degree angle, as they will be installed.

2. Use a pencil to trace the profile of the first piece onto the second piece, creating a scribed line.

3. Transfer the scribed line to the backside of the second piece, 1/16 inch away from the original line (or less, depending on the gap between the pieces).

4. Use a combination square or miter gauge to align the saw blade perpendicular to the scribed line on the back of the second piece.

5. Cut along the scribed line, using a fine-toothed saw (such as a coping saw or a miter saw with a fine-toothed blade).

6. Hold the cut pieces together again to check the fit. If necessary, make small adjustments to the cut until a tight and seamless joint is achieved.

7. Apply wood filler to any small gaps and sand it smooth once it dries.

8. To ensure a precise and seamless miter at the inner corner, consider using a technique called “back cutting.” This involves cutting through the backside of the second piece (the one being scribed) slightly farther than the scribed line, along a 45-degree angle. This creates a small “step” that allows the two pieces to fit together more snugly and eliminates any gaps.

Cleaning Up and Finishing the Cut

After making your cuts, it’s important to clean up the edges and finish the cut to ensure a seamless and professional-looking result.

Sanding the Edges:

Using fine-grit sandpaper (220-grit or higher), lightly sand the edges of the cut to remove any rough or uneven areas.
Sand in the direction of the grain to avoid scratching or damaging the surface.

Filling Gaps:

If there are any small gaps between the quarter round and the wall or the other piece of trim, fill them using a paintable caulk or wood filler.
Apply the caulk or filler with a putty knife or your finger, and smooth it out to create a flush surface.

Trimming Excess Caulk:

Once the caulk or filler has dried, use a sharp utility knife to trim off any excess material that extends beyond the edges of the quarter round.
Hold the knife at a 45-degree angle to the surface and gently scrape away the excess caulk or filler.

Applying Touch-Up Paint:

If necessary, apply touch-up paint to the cut edges or any areas where the paint may have been scratched or damaged during the process.
Use a small brush to apply the paint carefully, matching the color of the existing finish.

Sanding Grit
220-grit or higher

Additional Tips for a Perfect Cut

With some practice and attention to detail, you can achieve a professional-looking inside quarter-round cut every time. Here are some additional tips:

**Use a sharp saw:** A dull saw will tear the wood, resulting in a less precise cut. Ensure your saw is sharp and clean before cutting.
**Secure the wood:** Clamp the quarter-round in place on a stable work surface to prevent it from moving during the cut.
**Mark the cut line accurately:** Use a pencil and ruler to mark the precise angle and length of the cut. Double-check your measurements before cutting.
**Cut slowly and carefully:** Take your time and saw through the quarter-round steadily. Avoid applying excessive pressure or sawing too quickly, as this can cause splintering or tear-out.
**Sand the cut edges:** Smooth any rough edges or splinters from the cut with sandpaper. This will give the cut a clean, finished look.
**Test the fit before gluing:** Hold the cut quarter-round in place to ensure it fits perfectly before applying any adhesive.
**Practice on scrap wood:** If you are new to cutting quarter-round, it’s a good idea to practice on scrap wood first to get the hang of the technique.
**Don’t over-complicate it:** Cutting quarter-round inside corners may seem daunting, but it’s a simple process with a little patience and care.
**Use a miter box:** A miter box can help ensure precise 45-degree angles for the cuts.
**Double-miter for a tighter fit:** If desired, you can double-miter the quarter-round to create an even tighter fit, especially for inside corners with a smaller radius.

How To Cut Quarter Round Inside Corner

To cut inside corners when using quarter round, miter cuts must be made to join the pieces together perfectly.

1. Place the quarter round on the wall where it will be installed, aligning the bottom edge with the baseboard and the inside edge with the corner.

2. Use a pencil to trace the outline of the quarter round at the corner.

3. Cut two pieces of quarter round to the same length that will line up with your previously drawn line.

4. Place the two pieces of quarter round in a miter box and secure them with the clamps.

5. Use a miter saw to cut both pieces of quarter round at once.

6. Dry fit the pieces together to make sure they fit properly.

7. If the pieces fit together properly, apply adhesive to the back of one of the pieces and press it into place.

8. Repeat this process with the other piece of quarter round.

9. Use a nail gun to secure the pieces of quarter round to the wall.

10. Fill any nail holes with wood filler and allow it to dry.

11. Paint or stain the quarter round to match the rest of the trim.

7 Steps on How to Cut a Quarter Round

If you’re looking for a way to add a decorative touch to your home, quarter round molding is a great option. It’s a versatile molding that can be used to trim out windows, doors, and baseboards. It can also be used to create decorative moldings and frames. Cutting quarter round molding is a simple process that can be done with a few basic tools. Here’s a step-by-step guide on how to cut a quarter round:

First, measure and mark the length of the quarter round you need to cut. Use a miter saw to cut the quarter round at a 45-degree angle. Be sure to hold the quarter round firmly in place while you’re cutting it. Once you’ve cut the quarter round, you can use a sandpaper to smooth the edges. Finally, you can install the quarter round using nails or glue.

Choosing the Right Tools and Materials

Quarter round is a type of molding used to cover the gap between the floor and the wall, or to trim around windows and doors. It is typically made from wood, but it can also be made from plastic or metal. To cut quarter round, you will need the following tools and materials:

Tools:

Miter saw
Measuring tape
Pencil
Safety glasses

Materials:

Quarter round molding

Types of Miter Saws

There are two main types of miter saws: sliding miter saws and compound miter saws. Sliding miter saws are the most common type of miter saw, and they are a good choice for cutting quarter round. Compound miter saws can make both miter cuts and bevel cuts, which can be useful for cutting quarter round that needs to be installed around a corner.

When choosing a miter saw, it is important to consider the following factors:

Factor	Considerations
Blade size	The blade size will determine the maximum thickness of quarter round that you can cut.
Motor power	The motor power will determine the speed and accuracy of the cuts.
Miter range	The miter range will determine the range of angles that you can cut.
Bevel range	The bevel range will determine the range of angles that you can cut.

Measuring and Marking the Quarter Round

Step 1: Determine the Length of the Quarter Round

* Use a measuring tape to measure the length of the area where the quarter round will be installed.
* Add 1 inch for overlap at each end. For example, if the area measures 10 feet, cut the quarter round to 10 feet 2 inches.

Step 2: Mark the Starting Point

* Measure the distance from the end of the wall or surface to the first point where the quarter round will be installed.
* Mark this point on the back of the quarter round.

Step 3: Mark the Overlap Points

* Measure and mark a point on the back of the quarter round that is equal to the length of the overlap (1 inch).
* Measure and mark another point that is 1 inch shorter than the length of the quarter round.

Step 4: Draw a Line on the Quarter Round

* Using a pencil or chalk, connect the starting point to the first overlap point.
* Continue drawing a line from the first overlap point to the second overlap point.
* This line will serve as a cutting guide.

Markings	Distance from the End
Starting point	Measured distance from the wall
First overlap point	1 inch
Second overlap point	Length of the quarter round – 1 inch

Making Clean Cuts with a Miter Saw

If you need to make precise, clean cuts in quarter round, a miter saw is the ideal tool. Here’s how to use a miter saw effectively:

1. Measure and Mark Your Cut

Determine the desired length of the quarter round and mark it with a pencil or measuring tape. Make sure the mark is perpendicular to the edge of the material.

2. Set Up Your Miter Saw

Adjust the saw’s blade to a 45-degree angle and ensure that the fence is parallel to the blade. Securely clamp the quarter round to the saw table.

3. Make the Cut

Slowly bring the saw blade down onto the quarter round, applying light pressure. Hold the material firmly against the fence and allow the blade to cut through. Repeat the process for the other side.

4. Fine-tune the Cut

If the cut is not perfectly flush or smooth, you can use a sander or hand plane to gently remove any excess material. Be careful not to over-sand or plane, as this could weaken the joint.

Miter Saw Tip
Use a sharp saw blade to ensure clean, precise cuts.
Use a featherboard to provide support and prevent the material from splintering.
Wear safety glasses and gloves while operating the saw.
Practice making cuts on scrap material before attempting to cut the actual quarter round.

Using a Circular Saw for Straight Cuts

A circular saw is a versatile tool that can be used to make straight cuts in quarter round. Here are the steps on how to use a circular saw to cut quarter round:

Measure and mark the cut line. Use a tape measure and pencil to mark the cut line on the quarter round.
Set the depth of the saw. The depth of the saw should be set to slightly less than the thickness of the quarter round.
Adjust the saw blade. The saw blade should be adjusted to a 90-degree angle to the base of the saw.
Secure the quarter round. Clamp the quarter round to a sturdy work surface.
Make the cut. Hold the saw firmly and slowly guide it along the cut line. Be sure to keep the saw blade perpendicular to the quarter round.

Detailed Guide to Step 5: Making the Cut

Position the saw’s base plate firmly against the workpiece, ensuring the blade extends slightly beyond the opposite side.
Engage the saw’s motor and gradually apply downward pressure while guiding it along the cut line.
Maintain a steady, even pace while cutting, avoiding sudden movements or excessive force.
Check the cut periodically to ensure it’s clean and accurate.
Once the cut is complete, release the trigger and allow the saw to come to a complete stop before lifting it away.

Guide to Using a Coping Saw for Curves

6. Sawing in Curved Cuts: Detailed Steps

**Step 1: Secure the Quarter Round in Place:** Clamp the quarter round to a stable surface, such as a workbench, using a C-clamp or vise. Ensure that the edge you intend to cut is exposed and accessible.

**Step 2: Start the Cut at a Sharp Angle:** Align the coping saw blade at a sharp angle to the quarter round’s surface, just inside the line you marked. Start sawing gently, applying light pressure.

**Step 3: Follow the Curve:** As you saw, gradually adjust the saw’s angle to follow the curve. Use your fingers as a guide to feel the shape of the curve and maintain precision.

**Step 4: Remove the Waste Material:** Stop sawing when you reach the end of the curve. Use a sharp chisel or utility knife to carefully remove the waste material from the inside of the cut.

**Step 5: Clean Up the Cut:** Sand the edges of the cut to smooth any rough spots. Use fine-grit sandpaper for a professional finish.

Handy Tips for Using a Coping Saw

Tip	Benefit
Use new or sharp blades	Clean, precise cuts
Hold the saw perpendicular to the surface	Accurate and stable cuts
Saw at a slow, steady pace	Control and precision

Techniques for Cutting Complex Angles

1. Master Measuring and Marking

Accurately measuring and marking the angle you need to cut is crucial. Use a protractor or angle finder to determine the angle accurately, and mark it precisely on the quarter round.

2. Use a Miter Saw

A miter saw is the most efficient tool for cutting complex angles. Set the saw to the desired angle and secure the quarter round firmly in place. Practice on scrap pieces before cutting your actual trim.

3. Employ a Compound Miter Saw

Compound miter saws allow you to cut both miters and bevels. This versatility is ideal for complex angles that involve both vertical and horizontal cuts.

4. Utilize a Coping Saw

A coping saw is a manual saw that is well-suited for cutting intricate curves and tight angles. Carefully guide the saw along the marked line, and use a steady hand to maintain precision.

5. Employ a Jigsaw

Similar to a coping saw, a jigsaw can cut complex angles, but it is better suited for longer cuts. Use a fine-toothed blade to minimize tear-out and achieve a clean cut.

6. Draw a Reference Line

For angles that intersect with a straight edge, draw a reference line perpendicular to the edge and extending from the point where the angled cut begins. Use this line as a guide for cutting.

7. Double-Check and Fine-Tune

Once you have cut the angle, double-check its accuracy by measuring it against the original marking or using a miter gauge. If necessary, make fine adjustments using a sanding block or hand plane to achieve a perfect fit.

Safety Precautions

Before beginning any cutting operation, it is crucial to prioritize safety. Here are some essential precautions to take:

Wear safety glasses to protect your eyes from flying debris.
Use a sharp blade to minimize the force required for cutting and prevent splintering.
Secure the quarter round firmly to prevent it from moving during cutting.
Never attempt to freehand cut the quarter round.

Best Practices

To achieve a clean and precise cut, follow these best practices:

Use a miter saw or a miter box with a sharp blade specifically designed for cutting molding.
Measure and mark the desired cut length accurately.
Align the quarter round in the miter saw or miter box and clamp it securely.
Hold the saw or miter box steady and guide the blade through the cut.
Make multiple light passes instead of trying to cut through the quarter round in one stroke.
Check the cut for accuracy before removing the quarter round from the saw or miter box.
Sand any rough edges or splinters to create a smooth finish.

8. Using a Miter Saw with a Crown Molding Attachment

For intricate cuts, such as angles that differ from 90 degrees, a miter saw with a crown molding attachment can provide greater precision. Here are step-by-step instructions on how to use this specialized tool:

Step 1: Attach the crown molding attachment to the miter saw according to the manufacturer’s instructions. Step 2: Set the desired cut angle on both the saw and the crown molding attachment. Step 3: Secure the quarter round in the crown molding attachment. Step 4: Hold the saw steady and guide the blade through the cut while supporting the quarter round with your free hand. Step 5: Remove the quarter round from the crown molding attachment and check the cut for accuracy.

Common Pitfalls and Troubleshooting

1. Splitting the Quarter Round

This can happen if you apply too much pressure when cutting. Use a sharp blade and a light touch to prevent this.

2. Cutting the Quarter Round Too Short

Measure carefully before cutting to ensure the quarter round is the correct length.

3. Cutting the Quarter Round at an Incorrect Angle

Use a miter saw or miter box to ensure the cut is at a precise 45-degree angle.

4. Not Sanding the Cut Surface

Sanding the cut surface will smooth any rough edges and improve the overall finish.

5. Leaving Gaps Between the Quarter Round and the Wall

Use caulk or wood filler to fill any gaps and create a seamless transition.

6. Not Using the Right Type of Adhesive

Use a construction adhesive specifically designed for quarter round to ensure a strong bond.

7. Not Using Enough Adhesive

Apply a generous amount of adhesive to the back of the quarter round for a secure hold.

8. Not Pressing the Quarter Round Firmly into Place

Press down firmly on the quarter round after applying adhesive to ensure good contact with the wall.

9. Cutting the Quarter Round Incorrectly for an Inside Corner

A common mistake is cutting both pieces of quarter round at 45 degrees. This will result in a gap at the corner. Instead, cut one piece at 45 degrees and the other at 30 degrees to create a snug fit.

Inside Corner Cut

Outside Corner Cut

Piece 1: 45 degrees

Piece 2: 30 degrees

Piece 1: 45 degrees

Piece 2: 45 degrees

Tips for Achieving Professional-Grade Results

1. Use a Sharp, Fine-Tooth Saw

A fine-tooth saw will give you a clean, precise cut. Avoid using a coarse-tooth saw, as it will tear the wood and leave a rough edge.

2. Measure and Mark Carefully

Take your time to measure and mark where you want to cut. Use a pencil and a ruler to make precise markings.

3. Support the Workpiece

Make sure the workpiece is securely supported before you start cutting. This will help prevent the piece from moving around and damaging the cut.

4. Cut Slowly and Carefully

Take your time and don’t force the saw. Let the saw do the work and cut through the wood gradually.

5. Use a Miter Box

A miter box is a tool that helps you cut accurate angles. If you need to make a mitered cut, use a miter box to ensure precision.

6. Sand the Cut

Once you have made the cut, sand the edges to smooth any rough areas.

7. Use a Finishing Nailer

If you are attaching the quarter round to a wall or other surface, use a finishing nailer to drive the nails into place. This will give you a clean, professional-looking finish.

8. Fill the Nail Holes

After you have driven the nails into place, fill the nail holes with wood filler. This will help to conceal the nails and give the surface a finished look.

9. Use a Caulk Gun

If there are any gaps between the quarter round and the wall, use a caulk gun to fill them in. This will help to seal the joint and prevent drafts.

10. Add Trim

If desired, you can add trim to the top of the quarter round to give it a more finished look. There are a variety of trim options available, so you can choose one that matches your taste and decor.

Tool	Purpose
Miter saw	Cutting accurate angles
Table saw	Cutting straight lines
Circular saw	Cutting curves and irregular shapes
Jigsaw	Cutting intricate shapes
Drill	Drilling holes for nails or screws
Hammer	Driving nails
Nail gun	Driving nails quickly and efficiently
Sander	Smoothing rough edges
Caulk gun	Filling gaps and sealing joints
Trim	Adding a decorative touch

How To Cut A Quarter Round

Quarter round molding is a type of trim that is used to cover the gap between the baseboard and the floor. It can also be used to cover the gap between the ceiling and the wall. Quarter round molding is typically made from wood, but it can also be made from other materials such as plastic or metal.

To cut quarter round molding, you will need a miter saw. A miter saw is a type of saw that is used to make angled cuts. To cut a miter cut, you will need to set the saw to the desired angle. The angle will depend on the type of cut that you are making. For example, if you are cutting a miter cut for a corner, you will need to set the saw to a 45-degree angle.

Once you have set the saw to the desired angle, you can place the quarter round molding on the saw table. Make sure that the molding is aligned with the saw blade. Then, slowly lower the saw blade onto the molding. Be careful not to press down too hard, as this could cause the molding to break.

Once the saw blade has cut through the molding, you can remove the molding from the saw table. You can then use the miter cut to create a corner or to cover a gap.

5 Ways To Cut Inside Corners On Quarter Round

Quarter round is a type of molding that is used to cover the joint between two surfaces, such as the floor and the wall. It is typically made of wood or plastic, and it comes in a variety of sizes and shapes. One of the most common types of quarter round is inside corner quarter round, which is used to cover the joint between two walls. Cutting inside corners on quarter round can be a bit tricky, but it is not impossible. With a little practice, you can get the hang of it and create beautiful, professional-looking results.

To cut inside corners on quarter round, you will need a miter saw. A miter saw is a type of saw that is used to make angled cuts. It is important to use a miter saw for this project because it will help you to make precise cuts. If you do not have a miter saw, you can rent one from your local hardware store. Once you have your miter saw, you can begin cutting the inside corners on your quarter round.

To cut an inside corner on quarter round, you will need to first measure the length of the joint that you will be covering. Once you have the measurement, you can cut two pieces of quarter round to the desired length. To cut the inside corner, you will need to place the two pieces of quarter round on the miter saw and cut them at a 45-degree angle. Once you have cut the inside corner, you can attach the two pieces of quarter round to the joint using adhesive or nails.

Measure and Mark the Inside Corner

Determining the angle and length of the corner cut requires careful measurement and marking. Follow these steps to accurately lay out the cut:

Step 1: Determine the Angle

Measure the angle between the two walls forming the inside corner using a protractor or digital angle finder. If the angle is not exactly 90 degrees (a square corner), the quarter round will need to be beveled to match the angle.

Step 2: Measure and Mark the Length

Measure the distance from the point where the walls meet to the edge of the room. This measurement represents the length of the quarter round that will be cut for the inside corner. Mark this length onto the quarter round using a measuring tape and pencil.

Step 3: Draw the Bevel (If Necessary)

If the inside corner is not 90 degrees, it will be necessary to draw a bevel on the quarter round. Determine the angle of the bevel by dividing the measured angle by 2. For example, if the inside corner measures 80 degrees, the bevel angle would be 40 degrees.

Inside Corner Angle	Bevel Angle
80°	40°
75°	37.5°
60°	30°
45°	22.5°

Using a protractor or bevel gauge, draw a line at the appropriate bevel angle from the mark you made in Step 2. This line will guide you when cutting the quarter round.

Make a Test Cut

Before you start cutting the inside corners of your quarter round, it’s a good idea to make a test cut on a scrap piece of material. This will help you to get the hang of the technique and to make sure that you have the right saw blade and settings.

To make a test cut, follow these steps:

Set the saw blade to the correct angle. The angle will vary depending on the thickness of your quarter round, but it is typically between 45 and 60 degrees.
Clamp the scrap piece of material to your work surface.
Hold the saw firmly and make a cut through the material.
**Make sure to keep your fingers out of the way of the blade.**
Inspect the cut to make sure that it is clean and precise.

Once you are satisfied with your test cut, you can proceed to cutting the inside corners of your quarter round.

Quarter Round Thickness	Saw Blade Angle
1/4 inch	45 degrees
3/8 inch	50 degrees
1/2 inch	60 degrees

Fill any Gaps

Any gaps between the quarter round and the wall can be filled with either caulk or wood filler. Caulk is a better choice for small gaps, while wood filler is better for larger gaps.

Using Caulk:

Apply a bead of caulk along the gap between the quarter round and the wall.

Smooth the caulk with your finger or a damp cloth.

Using Wood Filler:

Mix the wood filler according to the manufacturer’s instructions.

Apply the wood filler to the gap between the quarter round and the wall using a putty knife.

Smooth the wood filler with your finger or a damp cloth.

After the caulk or wood filler has dried, you can paint it to match the color of the quarter round.

Pros of using caulk Cons of using caulk

Easy to apply Not as durable as wood filler

Can be used to fill small gaps Can shrink over time

Pros of using wood filler Cons of using wood filler

More durable than caulk Can be difficult to apply

Can be used to fill both small and large gaps Can be difficult to sand or paint

Pros of using caulk	Cons of using caulk
Easy to apply	Not as durable as wood filler
Can be used to fill small gaps	Can shrink over time

Pros of using wood filler	Cons of using wood filler
More durable than caulk	Can be difficult to apply
Can be used to fill both small and large gaps	Can be difficult to sand or paint

Sand and Finish

Once the quarter round is cut and installed, it’s time to sand and finish it to match the rest of the trim. Here are the steps:

1. Sand Rough Edges

Use a sanding sponge or fine-grit sandpaper to smooth out any rough edges or splinters. Sand with the grain of the wood, and be careful not to over-sand.

2. Fill Nail Holes

If you used nails to secure the quarter round, fill the nail holes with wood filler. Let the filler dry completely, then sand it flush with the surface.

3. Apply Primer

Apply a coat of primer to the quarter round using a brush or roller. Primer helps the paint adhere better and provides a smooth finish.

4. Paint Quarter Round

Paint the quarter round with two coats of latex paint in the desired color. Allow each coat to dry completely before applying the next.

5. Caulk Joints

Apply a thin bead of caulk to the joints between the quarter round and the wall or baseboard. Use a damp cloth to smooth the caulk and remove any excess.

6. Touch Up

Inspect the quarter round for any imperfections or missed spots. Touch up the paint or caulk as needed.

7. Protect the Finish

Consider applying a clear coat of polyurethane or varnish to protect the finish and make it more durable.

8. Enjoy the Results

Once the quarter round is sanded and finished, it will add a clean, professional touch to your home.

9. Detailed Guide to Sanding Inside Corners

Sanding inside corners can be tricky, but with the right technique, you can achieve a smooth, professional finish:

Use a sanding sponge or fine-grit sandpaper.
Hold the sandpaper perpendicular to the surface of the corner.
Gently sand in a circular motion, moving from the inside of the corner outward.
Avoid using excessive force, as this can cause the sandpaper to tear.
Check the progress frequently and stop sanding when the corner is smooth and even.

Tool	Function
Sanding sponge	Versatile tool for sanding small areas and contours
Fine-grit sandpaper	For smooth, final sanding
Wood filler	To fill nail holes and imperfections
Primer	Prepares the surface for paint
Latex paint	Durable and easy to apply
Caulk	To seal joints and prevent moisture damage

How To Cut Inside Corners On Quarter Round

To cut inside corners on quarter round, you will need a miter saw or a coping saw. If you are using a miter saw, set the saw to a 45-degree angle. Place the quarter round on the saw table with the inside corner facing up. Align the saw blade with the inside corner and make the cut. If you are using a coping saw, insert the coping saw blade into the inside corner of the quarter round. Hold the saw perpendicular to the quarter round and cut along the inside corner. Be sure to cut slowly and carefully to avoid splintering the wood.

Once you have cut the inside corner, you will need to miter the ends of the quarter round. To do this, set your miter saw to a 45-degree angle. Place the quarter round on the saw table with the mitered end facing up. Align the saw blade with the mitered end and make the cut. Repeat this process for the other end of the quarter round.

Once you have mitered the ends of the quarter round, you can install it on the wall. Apply a bead of caulk to the back of the quarter round and press it into place. Use a nail gun to secure the quarter round to the wall. Be sure to countersink the nails so that they are below the surface of the wood.