Tag: diy-garage-door-repair

6 Easy Steps to Adjust Garage Door Springs

6 Easy Steps to Adjust Garage Door Springs
$title$

Garage door springs are an essential part of your garage door system. They help to lift and lower the door, and they provide tension to keep the door in place. Over time, springs can wear out or break, which can cause the door to become difficult to open or close. If you’re experiencing problems with your garage door, it’s important to check the springs to see if they need to be adjusted or replaced.

Adjusting garage door springs is a relatively simple task that can be completed in a few minutes. However, it’s important to take safety precautions and follow the instructions carefully. First, gather the tools you’ll need, including a socket wrench, a screwdriver, and a pair of pliers. Next, locate the springs on your garage door. They’re typically located on either side of the door, near the top. Once you’ve found the springs, you can begin to adjust them.

To adjust the springs, you’ll need to loosen the bolts that hold them in place. Once the bolts are loose, you can turn the springs to adjust the tension. Be sure to turn the springs in small increments, and test the door after each adjustment. Once you’ve adjusted the springs to the correct tension, tighten the bolts back down. With a little care and attention, you can easily adjust your garage door springs and get your door working smoothly again.

The Importance of Balanced Garage Door Springs

The Garage Door Spring System

Your garage door spring system is what enables you to open and close the door smoothly and effortlessly. It consists of two springs, one on each side of the door, that are connected to the door and to the frame of the garage. When the door is closed, the springs are compressed; when it is open, the springs are extended. The springs provide the counterbalance to the weight of the door, making it easy to lift and lower.

Why is Balance Important?

Balanced springs are essential for the proper functioning of your garage door. If the springs are not balanced, the door will be difficult to open and close, and it could even come off its tracks. In addition, unbalanced springs can put excessive stress on the door and its components, leading to premature wear and tear.

Signs of Unbalanced Springs

Sign Cause
The door is difficult to open or close The springs are not providing enough counterbalance to the weight of the door.
The door opens or closes too quickly The springs are providing too much counterbalance to the weight of the door.
The door is crooked or off-track The springs are not providing even counterbalance to the weight of the door, causing it to sag or bind.

If you notice any of these signs, it is important to have your garage door springs checked and balanced by a qualified technician.

Identifying the Type of Garage Door Springs

Garage door springs work by storing potential energy to counterbalance the weight of the door, making it easier to lift. There are two main types of springs used in garage doors: extension springs and torsion springs.

Extension Springs

Extension springs are mounted on the horizontal tracks above the door opening. When the door is closed, they are stretched. As the door opens, they contract, providing the force to lift the door. Extension springs are typically used on doors with standard heights and relatively light weight.

To identify extension springs, look for the following characteristics:

  • Mounted on horizontal tracks
  • Stretched when the door is closed
  • Contract as the door opens

Torsion Springs

Torsion springs are mounted on a metal shaft above the door opening. When the door is closed, they are twisted. As the door opens, they untwist, providing the force to lift the door. Torsion springs are typically used on heavier doors or doors with high-lift mechanisms.

Extension Springs Torsion Springs
Mounted on horizontal tracks Mounted on a metal shaft
Stretched when the door is closed Twisted when the door is closed
Contract as the door opens Untwist as the door opens

To identify torsion springs, look for the following characteristics:

  • Mounted on a metal shaft
  • Twisted when the door is closed
  • Untwist as the door opens

Gathering the Necessary Tools and Equipment

To properly adjust garage door springs, you will need to gather the following tools and equipment:

  1. Wrench: A crescent wrench or socket wrench is necessary for tightening and loosening the adjusting nuts on the springs.
  2. Pliers: Pliers are used for holding the safety cables in place while adjusting the springs.
  3. Screwdriver: A screwdriver may be required to remove or install safety cables.
  4. Clamps: Clamps are used to hold the springs in place while making adjustments.

    Safety Precautions:

    • Garage door springs are under extreme tension and can cause serious injury if not handled properly.
    • Always wear safety glasses and gloves when working with garage door springs.
    • Do not attempt to adjust springs if you are not confident in your abilities.
    • If you are unsure about any aspect of spring adjustment, consult a professional.

    It is important to ensure that the springs are properly adjusted to maintain the correct balance of the garage door. If the springs are too tight, the door will be difficult to open and close. If the springs are too loose, the door may not be able to stay open and could come crashing down.

    Lubricating Garage Door Springs

    Regular lubrication of your garage door springs is crucial for their longevity and smooth operation. Here are step-by-step instructions for lubricating your springs:

    Step 1: Gather Your Materials

    You will need the following materials:
    – Lithium-based grease or commercial garage door spring lubricant.
    – Step ladder.
    – Rags or paper towels.
    – Safety gloves.

    Step 2: Safety First

    Before you begin, disconnect the garage door opener from the power supply. Engage the manual release cord to disengage the door from the opener.

    Step 3: Inspect the Springs

    Carefully inspect the springs for any wear, corrosion, or damage. If you notice any concerns, contact a qualified technician for professional assistance.

    Step 4: Apply Lubricant to the Coils

    Using a grease gun or a cloth, apply a thin layer of lubricant to the coils of the spring. Ensure that the lubricant is evenly distributed and penetrates the coils thoroughly.

    Step 5: Lubricate the Hinges

    Lubricate the spring hinges and any other moving parts where metal-on-metal contact occurs. Apply lubricant sparingly to avoid over-lubrication.

    Step 6: Wipe Away Excess Lubricant

    Use a rag or paper towel to wipe away any excess lubricant that may have spilled onto the floor or other surfaces. This will prevent dirt and debris from sticking to the lubricant.

    Step 7: A More Detailed Guide to Lubricating the Hinges

    To ensure thorough lubrication of the hinges, follow these steps:
    – Apply lubricant to the hinge pin using a grease gun or a small brush.
    – Open and close the door several times to distribute the lubricant evenly.
    – Wipe away any excess lubricant and inspect the hinges for smooth operation.

    Testing the Garage Door Balance

    Assessing the balance of your garage door is crucial before adjusting the springs. To test the balance, follow these steps:

    1. Disconnect the Automatic Opener: Pull the release cord to disengage the opener from the door.
    2. Manually Lift the Door: Lift the garage door halfway up using the manual release handle.
    3. Let Go: Slowly let go of the door. It should remain in place without moving.
    4. Observe the Movement: If the door starts to fall down, it’s out of balance and requires additional tension on the springs.
    5. Counterbalance with a Weight: If the door starts to rise, it’s overbalanced. Place a weight (such as a sandbag or tool) on the ground in front of the door to counterbalance it.
    6. Adjust the Weight: Keep adjusting the weight until the door stays still when let go.
    7. Safety Precautions: Follow all safety precautions, including wearing gloves and using appropriate tools. Do not lift the door if you have any physical limitations.
    8. Table: Garage Door Balance Test Results
      Observation Action Required
      Door falls down Tighten the springs
      Door rises up Loosen the springs
      Door stays still Balanced, no adjustment needed

    When to Call a Professional

    Garage Door Not Opening or Closing Properly

    If your garage door is stuck or only opens partially, it’s likely due to a problem with the springs. Attempting to adjust them yourself without proper knowledge and safety precautions can be dangerous. In such cases, it’s highly recommended to call a professional.

    Excessive Noise During Operation

    Loud noises, such as banging, grinding, or rattling, can indicate a problem with the springs. These noises may signal that the springs are misaligned, damaged, or need lubrication. Ignoring these noises can worsen the issue and potentially cause further damage.

    Visible Damage or Rust

    Inspect the springs periodically for any visible damage, cracks, or rust. If you notice any abnormalities, it’s important to call a professional immediately. Damaged springs can snap and cause severe injury or damage to your vehicle.

    Frequent Adjustments Required

    If you find yourself constantly adjusting the springs, it’s likely a symptom of a larger issue. Springs should not need frequent adjustments; excessive adjustments may indicate a problem with the door’s balance or other components.

    Improper Spring Tension

    Determining the correct tension for your garage door springs is crucial. If the springs are too tight, it can put excessive strain on the door and opener, leading to premature failure. Conversely, springs that are too loose will not provide enough support and can cause the door to sag or malfunction.

    Lack of Safety Features

    Modern garage doors are equipped with safety features, such as pinch protection and auto-reverse, which help prevent injuries. If your garage door lacks these features or they are not functioning properly, it’s recommended to call a professional to ensure the door meets safety standards.

    Personal Comfort and Safety

    While some homeowners may feel comfortable adjusting garage door springs themselves, it’s important to prioritize personal safety. Springs are under high tension and can snap if mishandled. If you are not confident in your abilities or concerned about potential injuries, it’s always best to seek professional assistance.

    Cost and Time Savings

    Hiring a professional may seem like an additional expense, but it can save you money and time in the long run. Attempting to adjust springs yourself without proper knowledge can result in further damage, which may be costly to repair. Professionals can diagnose and fix the issue quickly and efficiently, minimizing downtime and preventing potential hazards.

    Peace of Mind

    Knowing that your garage door is functioning properly and meets safety standards provides peace of mind. When you hire a professional to adjust the springs, you can rest assured that the job is done correctly and to the highest standards.

    How to Adjust Garage Door Springs

    If your garage door is not opening or closing properly, it may be due to a problem with the springs. Garage door springs are responsible for providing the tension needed to lift and lower the door. Over time, these springs can stretch or break, causing the door to become unbalanced or even inoperable.

    If you are experiencing problems with your garage door, it is important to adjust the springs. Adjusting the springs is a relatively simple task that can be completed in a few hours. However, it is important to take safety precautions when working with springs, as they can be dangerous if they are not handled properly.

    To adjust garage door springs, you will need the following tools:

    • Wrench
    • Screwdriver
    • Clamps
    • Safety glasses
    • Gloves

    Once you have gathered the necessary tools, you can begin adjusting the springs. First, you will need to determine which type of springs your garage door has. There are two main types of garage door springs: torsion springs and extension springs.

    Torsion springs are located above the garage door and are connected to a shaft. Extension springs are located on either side of the garage door and are connected to the door itself. To determine which type of springs your garage door has, simply look at the way they are mounted.

    People Also Ask About How to Adjust Garage Door Springs

    How do I know if my garage door springs need to be adjusted?

    There are a few signs that indicate that your garage door springs need to be adjusted. These signs include:

    • The door is difficult to open or close.
    • The door opens or closes unevenly.
    • The door makes a squealing or grinding noise when it is opened or closed.

    How often should I adjust my garage door springs?

    Garage door springs should be adjusted every few years, or more often if you live in an area with extreme weather conditions. Adjusting the springs will help to keep the door operating smoothly and prevent it from becoming damaged.

    Can I adjust garage door springs myself?

    Yes, you can adjust garage door springs yourself. However, it is important to take safety precautions when working with springs. If you are not comfortable working with springs, you should hire a professional to do the job.

5 Easy Steps to Adjust Spring Tension on Garage Door

6 Easy Steps to Adjust Garage Door Springs

Adjusting the spring tension on your garage door is a simple task that can be completed in a few minutes. By following these steps, you can ensure that your garage door opens and closes smoothly and safely.

First, you need to gather some tools. You will need a pair of pliers, a screwdriver, and a ladder. Once you have your tools, you can begin the process of adjusting the spring tension. To start, locate the springs on your garage door. The springs are usually located on either side of the door, and they are attached to the door frame. Once you have located the springs, you need to determine which way to adjust them. If the door is opening too slowly, you need to tighten the springs. If the door is opening too quickly, you need to loosen the springs.

To tighten the springs, use the pliers to turn the nuts on the springs clockwise. To loosen the springs, turn the nuts counterclockwise. Be sure to turn the nuts only a small amount at a time, and test the door after each adjustment. Once you have adjusted the spring tension to the desired level, you can reattach the springs to the door frame and close the door.

Preparing for Adjustment

Before embarking on the adjustment process, it’s crucial to ensure safety and prepare adequately. Here’s a comprehensive checklist to guide you through:

1. Safety Precautions:

Garage door springs are under immense tension and can cause severe injuries if mishandled. Prioritize safety by:

  • Disconnecting the garage door opener to prevent accidental activation.
  • Setting the ladder firmly on level ground, ensuring stability and preventing it from shifting or toppling.
  • Utilizing proper tools, such as a winding bar or a socket wrench, designed specifically for adjusting garage door springs.
  • Wearing protective gear, including gloves and safety glasses, to shield yourself from potential projectiles or flying debris.
  • Having a spotter present for assistance and an additional layer of safety.

2. Identifying the Spring Type:

Garage door springs come in various types, each requiring a specific adjustment method. Identify your spring type by visually inspecting the shape and configuration:

Spring Type Description
Torsion Spring Mounted on a shaft above the door and coiled around it
Extension Spring Attached to cables running alongside the tracks, extending when the door opens

3. Gathering the Necessary Tools:

To adjust garage door springs effectively, assemble the following tools:

  • Winding bar or socket wrench
  • Tape measure or ruler
  • Level
  • Lubricant (optional but recommended)

Identifying Spring Types

There are three main types of springs used in garage doors: torsion springs, extension springs, and oil-tempered springs.

1. Torsion Springs

Torsion springs are mounted on a shaft that runs across the top of the garage door opening. They are wound up when the door is closed and then unwind when the door is opened. Torsion springs are the most common type of spring used in garage doors.

2. Extension Springs

Extension springs are mounted on the sides of the garage door opening. They are stretched when the door is closed and then contract when the door is opened. Extension springs are less common than torsion springs, but they are sometimes used on smaller garage doors.

Extension springs are made of high carbon steel and are typically zinc plated for corrosion resistance. They come in a variety of sizes and strengths, depending on the weight and height of the garage door. The following table shows the different sizes and strengths of extension springs:

Spring Size Spring Strength Compatible Door Weight (lbs.)
1″ 100 lbs. 100-150
1-1/4″ 125 lbs. 150-200
1-1/2″ 150 lbs. 200-250
1-3/4″ 175 lbs. 250-300
2″ 200 lbs. 300-350

3. Oil-Tempered Springs

Oil-tempered springs are a type of extension spring that is made of high carbon steel and is then oil-tempered. This process makes the springs more durable and resistant to breakage. Oil-tempered springs are used on heavy garage doors.

Safety Precautions

When working with garage door springs, safety is paramount. Always keep these precautions in mind to avoid accidents and injuries:

  1. Wear protective gear: Wear gloves, safety glasses, and earplugs to protect yourself from flying debris and potential noise.
  2. Disconnect the opener: Unplug the garage door opener from the power source to prevent accidental operation while you work.
  3. Secure the door: Place a sturdy object, such as a block of wood or a heavy toolbox, under the bottom of the door to prevent it from suddenly dropping.
  4. Inspect the springs: Before attempting any adjustments, carefully inspect the springs for any signs of damage, wear, or corrosion. If you notice any abnormalities, do not attempt to adjust the springs and seek professional assistance.
  5. Use the proper tools: Always use the correct tools for the job. Do not attempt to adjust the springs with screwdrivers or other improper instruments.
  6. Be aware of spring force: Garage door springs are under immense tension. If not handled properly, they can cause serious injuries or damage to property. Never attempt to adjust the springs without proper training or experience.

Tools Required

Gathering the necessary tools before adjusting garage door spring tension is crucial for a successful and safe repair. Here’s a comprehensive list of essential tools you’ll need:










Tools Description
Ladder Sturdy and tall enough to reach the springs
Safety Glasses Protect your eyes from flying debris
Gloves Protect your hands from grease and splinters
Winding Bar Specialized tool for adjusting spring tension
Socket Wrench For adjusting nuts and bolts on the winding cones
Locking Pliers Hold the winding cones in place while adjusting
Flashlight For illuminating dark areas

Additionally, consider the following items for added safety and convenience:

  • Spring bar (for supporting the spring during adjustments)
  • Work gloves (for handling the springs)
  • Tape measure (for checking spring tension)
  • Flashlight (for illuminating the work area)

Locating Adjustment Bolts

To locate the adjustment bolts on your garage door spring system, follow these steps:

  1. Identify the spring type: There are two main types of garage door springs: torsion springs and extension springs. Torsion springs are mounted above the door opening, while extension springs run along the sides of the door.
  2. Safety first: Before adjusting the springs, ensure that the door is fully closed and that the release mechanism is engaged to prevent the door from moving.
  3. Locate the spring mountings: Torsion springs are mounted on a shaft or tube, while extension springs are attached to the door frame and the spring anchor. Locate these mountings on your garage door system.
  4. Inspect the bolts: On torsion springs, look for two bolts that are perpendicular to the shaft or tube. On extension springs, look for a single bolt that connects the spring to the anchor.
  5. Use the correct tools: You will need a socket wrench or an open-end wrench to adjust the bolts. The size of the wrench will vary depending on the size of the bolts on your spring system.

Additional Tips:

1. If you are not comfortable adjusting the spring tension yourself, consult a professional garage door repair technician.
2. Keep a notebook of the original bolt settings before making any adjustments.
3. Only make small adjustments at a time, and test the door’s operation before making further adjustments.

Determining Spring Tension

The tension of a garage door spring is crucial for the safe and proper operation of the door. Incorrect tension can lead to premature failure, safety hazards, or difficulty in opening or closing the door.

To determine the proper spring tension, follow these steps:

1. Disconnect the garage door opener: Unplug the opener or disconnect the power to the door.

2. Raise the door manually: With the opener disconnected, manually lift the door about halfway.

3. Observe the springs: Carefully examine the springs and look for any signs of damage or deformation.

4. Check the cable tension: The cables attached to the springs should be taut but not excessively tight.

5. Measure the spring diameter: Measure the diameter of the springs (measured from the center of the coils).

6. **Determine the spring type:** Identify the type of springs used on your garage door. Common types include torsion springs and extension springs.

Torsion Springs:

  • Mounted horizontally above the door
  • Tension is adjusted by winding or unwinding the spring using a winding bar
  • Refer to the spring manufacturer’s chart to determine the correct winding distance for your spring diameter and door weight

Extension Springs:

  • Mounted vertically on both sides of the door
  • Tension is adjusted by adding or removing coils from the spring
  • Refer to the manufacturer’s chart or use a spring scale to determine the correct number of coils for your door weight

Once you have determined the spring tension, refer to the manufacturer’s instructions for specific adjustment procedures. Adjust the springs carefully, following the manufacturer’s guidelines, and test the door’s operation thoroughly before reconnecting the garage door opener.

Making the Adjustments

Once you have identified the adjustment screws, it’s time to make the actual adjustments. Here’s how to do it:

1. Loosen the Adjusting Screw on the Weak Spring

Using a wrench or socket, loosen the adjusting screw on the spring that is causing the door to sag. Turn the screw counterclockwise to loosen it.

2. Tighten the Adjusting Screw on the Strong Spring

Now, turn your attention to the spring on the other side of the door. Using a wrench or socket, tighten the adjusting screw on this spring. Turn the screw clockwise to tighten it.

3. Repeat Steps 1 and 2

Repeat steps 1 and 2 until the door is level. You may need to make several adjustments to get the tension just right.

4. Check the Door’s Balance

Once you have made the adjustments, check the door’s balance by releasing it from the open position. If the door opens and closes smoothly, without any sagging or bouncing, then you have adjusted the tension correctly.

5. Lock the Adjusting Screws

Once you are satisfied with the tension, lock the adjusting screws in place. Turn the screws clockwise to tighten them.

6. Lubricate the Springs

To keep the springs working smoothly, lubricate them with a silicone-based lubricant. Apply the lubricant to the coils of the springs.

7. Troubleshooting: Springs Under Too Much Tension

If you find that the springs are under too much tension, you may notice the following symptoms:

The door is difficult to open and close, and you may feel a lot of resistance when you try to move it.

The door bounces back up when you try to close it.

The springs make a creaking or groaning sound when the door is moved.

If you are experiencing any of these symptoms, you should loosen the adjusting screws on the springs slightly. Start by loosening the screws on the weak spring, and then move on to the strong spring. Loosen the screws in small increments, and check the door’s balance after each adjustment.

Releasing Tension

Releasing the tension on a garage door spring can be a dangerous task if not performed correctly. It is important to take precautions and follow the steps below carefully to avoid injury.

  1. Gather your tools. You will need a pair of adjustable wrenches, a ladder, and a helper.
  2. Disconnect the garage door from the opener. This will prevent the door from opening or closing while you are working on it.
  3. Climb the ladder and locate the springs. There will be two springs on each side of the door.
  4. Use the adjustable wrenches to loosen the nuts on the bolts that hold the springs in place.
  5. Slowly lower the door until the tension on the springs is released.
  6. Once the tension is released, remove the bolts and springs from the door.
  7. Inspect the springs for damage. If there is any damage, the springs will need to be replaced.
  8. Reinstall the springs and bolts on the door. Make sure to tighten the nuts securely.
  9. Reconnect the garage door to the opener.
  10. Test the door to make sure it is working properly.

If you are not comfortable performing this task yourself, it is best to call a professional garage door repair technician.

Here is a table with some additional tips for releasing the tension on a garage door spring:

Tip Description
Use a helper Having a helper can make the task easier and safer.
Be careful not to overtighten the nuts Overtightening the nuts can damage the springs.
Test the door before using it This will ensure that the door is working properly.

Checking for Proper Function

To ensure that your garage door is functioning correctly, perform the following steps:

  1. Observe the door’s movement: Watch for any hesitations, jerking, or unusual noises during operation.

  2. Test the balance: Disconnect the opener and manually lift the door. It should remain balanced and stay open halfway when released.

  3. Inspect the tracks and rollers: Examine the tracks for any debris or damage that could impede smooth movement. Check the rollers for wear or loose bearings.

  4. Evaluate the springs: Look for any loose, broken, or misaligned springs. Springs should be evenly tensioned and not show signs of wear.

  5. Test the safety features: Ensure that the garage door reverses when it encounters an obstacle. Check the photo eyes for proper alignment and functionality.

  6. Adjust the limit switches: Adjust the limit switches so that the door opens and closes to the desired height and stops automatically.

  7. Check the opener’s performance: Run the opener through several cycles to monitor its operation. Listen for any strange noises or vibrations.

  8. Inspect the remote controls: Test the remotes to ensure they are functioning and have sufficient range.

  9. Check the keypad: If a keypad is installed, input the code several times to verify its functionality.

By thoroughly checking for proper function, you can ensure your garage door operates smoothly, safely, and reliably.

Resetting the Springs

If you have determined that the springs are too loose or too tight, you will need to reset them. To do this, first, disconnect the garage door opener from the springs by pulling the release cord or chain. Then, use a pair of pliers to remove the cotter pins that hold the springs in place. Once the cotter pins are removed, you can carefully remove the springs from the pulleys. Be careful not to let the springs snap back at you, as they can cause serious injury.

Adjusting the Springs

Once the springs are removed, you can adjust them to the correct tension. To do this, use a pair of pliers to bend the spring arms in or out. Bending the arms in will increase the tension, while bending them out will decrease the tension. Start by making small adjustments and then test the tension by opening and closing the garage door. Repeat this process until the tension is correct.

Troubleshooting

10. The garage door opens too slowly or too quickly

This could be caused by a number of issues, including:

  • The springs are too loose or too tight
  • The door opener is not properly adjusted
  • The door tracks are misaligned
  • The rollers are worn or damaged

To troubleshoot this issue, first, check the springs to make sure they are properly adjusted. Then, check the door opener to make sure it is properly installed and adjusted. If the springs and door opener are properly adjusted, then check the door tracks to make sure they are aligned. Finally, check the rollers to make sure they are not worn or damaged.

Possible Cause Solution
Springs are too loose Tighten springs
Springs are too tight Loosen springs
Door opener not properly adjusted Adjust door opener
Door tracks misaligned Align door tracks
Rollers worn or damaged Replace rollers

How to Adjust Spring Tension on a Garage Door

Garage door springs are an important part of the system, as they help to lift and lower the door smoothly and safely. Over time, springs can become loose or stretched, causing the door to become difficult to open or close. If you’re experiencing this problem, you may need to adjust the spring tension.

Here are the steps on how to adjust spring tension on a garage door:

  1. Safety first! Before you begin, make sure that the garage door is closed and the power is turned off.
  2. Identify the springs. Garage door springs are typically located above the door, on either side. They are usually made of metal and are wound around a shaft.
  3. Locate the adjustment nuts. The adjustment nuts are located on the ends of the springs. They are usually made of plastic or metal.
  4. Turn the adjustment nuts. To increase the spring tension, turn the nuts clockwise. To decrease the spring tension, turn the nuts counterclockwise.
  5. Test the door. Once you have adjusted the spring tension, open and close the door to test it. If the door is still difficult to open or close, you may need to adjust the tension further.

People also ask

How do I know if my garage door springs need to be adjusted?

There are a few signs that indicate that your garage door springs may need to be adjusted. These include:

  • The door is difficult to open or close.
  • The door opens or closes too quickly.
  • The door makes a grinding noise when opening or closing.

How often should I adjust my garage door springs?

Garage door springs should be adjusted every few years, or as needed. If you’re experiencing any of the problems listed above, you should adjust the springs sooner.

Can I adjust my garage door springs myself?

Yes, you can adjust your garage door springs yourself. However, it’s important to follow the safety precautions and instructions carefully.

If you’re not comfortable adjusting the springs yourself, you can call a professional garage door repair technician to do it for you.