Maintaining optimal hygiene is not only essential for your well-being but also for ensuring the longevity and performance of your CPAP equipment. Regular cleaning of your CPAP mask and hose is crucial in preventing bacteria and mold growth, reducing the risk of infections and ensuring a comfortable and effective sleep therapy. The SoClean 2 CPAP Cleaner and Sanitizer is a revolutionary device designed to make this process effortless and efficient. This article will provide a detailed guide on how to utilize the SoClean 2 to effectively clean your CPAP mask and hose, ensuring a cleaner and healthier breathing experience.

SoClean 2 is an automated CPAP cleaning and sanitizing system that eliminates the hassle of manual cleaning. By utilizing Activated Oxygen technology, it effectively kills 99.9% of bacteria and viruses that can accumulate on your CPAP mask and hose. The process is simple and convenient. Simply insert your mask and hose into the designated chamber, close the lid, and press the start button. The SoClean 2 will automatically cycle through a series of cleaning and sanitizing stages, leaving your equipment thoroughly disinfected in just two hours.

In addition to its effectiveness and ease of use, the SoClean 2 also offers several other benefits. It helps preserve the lifespan of your CPAP equipment by preventing damage caused by bacteria and mold growth. This can save you money in the long run by reducing the need for frequent replacements. Furthermore, the SoClean 2 is designed to be environmentally friendly, as it uses Activated Oxygen, which is a natural and non-toxic cleaning agent. The system is also quiet and discreet, making it suitable for use even while you sleep.

Preparation for Cleaning

Before you begin cleaning your SoClean 2 for mask and hose only, it is important to prepare the following:

Materials:

Item	Quantity
SoClean 2 Cleaner	1 tablet
SoClean 2 Cleaning Solution	1 cup

Instructions:

1. Gather materials: Make sure you have all the necessary materials before starting the cleaning process.

2. Check the cleaner: Inspect the SoClean 2 Cleaner tablet and ensure it is not chipped, cracked, or damaged. If it is damaged, discard it and use a new one.

3. Measure the cleaning solution: Using a measuring cup, carefully measure out 1 cup of SoClean 2 Cleaning Solution.

4. Set up the cleaner: Place the SoClean 2 Cleaner tablet in the designated compartment and fill the reservoir with the prepared cleaning solution.

5. Connect the mask and hose: Attach the mask and hose to the cleaner according to the manufacturer’s instructions. Ensure they are securely connected.

Connecting the SoClean 2 Device

To connect the SoClean 2 device, follow these steps:

Step 1: Unbox the SoClean 2 Device

Open the box containing the SoClean 2 device and remove all components.
Identify the following parts: the SoClean 2 device, the adapter, the hose, the mask adapter, and the user manual.

Step 2: Assemble the SoClean 2 Device

Attach the hose to the SoClean 2 device by inserting one end of the hose into the port on the back of the device and twisting it clockwise until it is secure.
Connect the adapter to the other end of the hose and twist it clockwise until it is secure.
Connect the mask adapter to the adapter and twist it clockwise until it is secure.
Insert the mask into the mask adapter and twist it clockwise until it is secure.

Step 3: Place the SoClean 2 Device

Place the SoClean 2 device on a flat surface near your bed or in a convenient location.
Make sure the device is not placed in a damp or humid environment.

Step 4: Connect the SoClean 2 Device to Power

Insert the adapter into a power outlet.
The SoClean 2 device will automatically turn on and start the cleaning cycle.

Component	Description
SoClean 2 device	The main unit that generates the ozone gas and sanitizes your CPAP equipment.
Adapter	Connects the SoClean 2 device to the power outlet.
Hose	Connects the SoClean 2 device to your CPAP mask and tubing.
Mask adapter	Connects the hose to your CPAP mask.
User manual	Provides instructions on how to use and maintain the SoClean 2 device.

Adding the Cleaning Solution

1. Fill the reservoir to the fill line with distilled water. Do not use tap water, as it can contain minerals that can damage the device.

2. Add one capful of SoClean 2 cleaning solution to the reservoir. Do not overfill.

3. **Preparing the Cleaning Solution:**

The SoClean 2 system requires a specific cleaning solution to be added to the water reservoir. This solution is formulated to effectively remove bacteria and mold from the mask and hose, while also being gentle on the equipment.

To prepare the cleaning solution, follow these steps:

Step	Description
1	Fill the water reservoir with distilled water up to the fill line.
2	Add one capful of SoClean 2 cleaning solution to the water reservoir.
3	Stir the solution thoroughly to ensure it is evenly mixed.

Once the solution is prepared, the device is ready to begin the cleaning process. It’s important to note that the cleaning solution should be replaced every 60 days for optimal performance and hygiene.

Inserting the Mask and Hose

1. Attach the Cleaning Cap to the Base Unit

Align the Cleaning Cap with the base unit and push it down until it clicks into place.

2. Insert the Mask into the Cleaning Cap

Remove the mask from your CPAP machine and firmly insert it into the Cleaning Cap, ensuring a tight fit.

3. Connect the Hose to the Cleaning Cap

Disconnect the hose from your CPAP machine and attach it to the Cleaning Cap, making sure it fits securely.

4. Insert the Hose into the Mask

Carefully insert the hose into the mask, ensuring it is fully connected and there are no gaps. To ensure a complete seal and prevent leaks, follow these additional steps:

a. Check for a Secure Connection

Gently pull on the hose to verify that it is securely connected to both the mask and the Cleaning Cap.

b. Adjust the Mask Position

If there are any leaks around the mask, adjust its position on your face to eliminate them.

c. Tighten the Hose

If necessary, gently tighten the hose connection by turning the collar clockwise until leaks are eliminated. Avoid overtightening the hose, as this could damage the connection.

Initiating the Cleaning Cycle

Once the Sooclean 2 is properly assembled, you can initiate the cleaning cycle by following these simple steps:

Power on the Sooclean 2:

Press the power button located on the top of the unit.
Select the desired cleaning mode:

Press the mode button repeatedly to cycle through the available modes (Mask Only, Hose Only, Mask and Hose, and UV Disinfection).
Place the mask or hose in the cleaning chamber:

Open the lid of the chamber and place the mask or hose inside, ensuring that it is securely seated on the base plate.
Close the lid and lock it in place:

Secure the lid by pressing down firmly on both sides until it clicks into position.

Start the cleaning cycle:

Press the start button on the front of the unit. The Sooclean 2 will begin its cleaning cycle, which typically takes around 5 minutes.

Cleaning Mode	Duration	Suitable for
Mask Only	5 minutes	CPAP and BiPAP masks
Hose Only	5 minutes	CPAP and BiPAP hoses
Mask and Hose	10 minutes	Complete CPAP or BiPAP system
UV Disinfection	30 minutes	CPAP and BiPAP masks and hoses

Removing the Mask and Hose

Once you’ve finished using your SoClean 2, it’s important to remove the mask and hose. Here are the steps on how to do it:

Turn off the SoClean 2 and unplug it from the power outlet.
Open the lid of the SoClean 2.
Grip the mask and hose firmly and pull them straight up to remove them from the SoClean 2.
Inspect the mask and hose for any damage. If there is any damage, do not use the mask or hose or the SoClean 2 and contact customer support.
Clean the mask and hose according to the manufacturer’s instructions.
Once the mask and hose are clean and dry, you can reattach them to the SoClean 2. To do this, simply insert the mask and hose into the SoClean 2 and push down until they click into place.

Cleaning the Mask and Hose

Component	Cleaning Method
Mask	Hand wash in warm, soapy water. Do not use bleach or harsh chemicals.
Hose	Wipe down with a damp cloth. Do not immerse in water.

How to Use SoClean 2 for Only Mask and Hose

Cleaning the SoClean 2 Unit

To clean the SoClean 2 unit, follow these steps:

Turn off the SoClean 2 unit and unplug it from the power outlet.
Remove the water chamber from the unit.
Empty the water chamber and rinse it with clean water.
Reinsert the water chamber into the unit.
Fill the water chamber with distilled water to the fill line.
Add 1 cleaning tablet to the water chamber.
Plug the SoClean 2 unit back into the power outlet and turn it on.
The SoClean 2 unit will begin to clean the mask and hose. The cleaning cycle will take approximately 2 hours.

Additional Tips for Cleaning the SoClean 2 Unit:

Clean the SoClean 2 unit monthly or more often if needed.
Use only distilled water in the water chamber.
Do not use bleach or other cleaning agents in the water chamber.
If the SoClean 2 unit is not cleaning properly, contact the manufacturer for troubleshooting assistance.

Cleaning Schedule	Frequency
Clean the SoClean 2 unit	Monthly or more often if needed
Empty the water chamber	After each use
Rinse the water chamber	After each use
Add a cleaning tablet to the water chamber	Monthly or more often if needed

Maintenance Schedule

To ensure optimal performance and hygiene, it is essential to follow the recommended maintenance schedule for your SoClean 2 device. The table below outlines the specific cleaning intervals and tasks:

Maintenance Task	Frequency
Clean Mask and Hose	Every night
Empty Water Tank	Every 2-3 days
Replace Water Cartridge	Every 6 months

Empty Water Tank

Empty the water tank every 2-3 days to prevent mold and bacteria growth. To empty the tank, simply detach it from the device and pour out the contents. Rinse the tank with clean water and reattach it to the device.

Replace Water Cartridge

Replace the water cartridge every 6 months to ensure optimal cleaning performance. To replace the cartridge, locate the cartridge compartment on the back of the device. Remove the old cartridge and insert the new one.

9. Sanitizing Mask and Hose

Sanitizing your mask and hose every night is crucial for maintaining hygiene and preventing the spread of bacteria. Follow these steps to ensure proper sanitization:

Remove the mask and hose from your CPAP machine.
Attach the mask and hose to the SoClean 2 device.
Turn on the device and activate the cleaning cycle.
The cleaning cycle will run for approximately 7 minutes.
Once the cycle is complete, remove the mask and hose from the device and reattach them to your CPAP machine.